h pb
-
h it
-
h dt
-
• C.GrP
IPt IN1 = ON IN2 = ON
0
1
x
2
x
3
x
x
(ode
prot
er.nr
updt
len
p.ty
eu.r
eu.s
ipt
xbb
SP.s
rp.t
So.t
St.y
0 ... 999
scale points
0.0 ... 99.59
0.0 ... 99.59
• StEP
0 ... 3
• ProG
ProG
Program number
Number of
program steps
1 ... 8
Program type and
restart mode
0 ... 127
Program type and restart mode
0
Restart from first step; the setpoint
copies the value of PV
1
Restart from conditions prior to stop
2
Restart with step search
(see “Programmer Functions”)
+ 8 Wait for STOP / START switching
+ 16 Continuous loop; at end of cycle the program restarts
from first step (ex32 function)
+ 32 At end of cycle the control output goes to “FAcP”
value, set in “CFG” menu
+64 Fast simulation (see “Programmer Functions”)
P0-0 ... P3-7
S step setpoint
Lo_L ... Hi_L
StEP
Selects program and
step to set
“S” step ramp time (time set
refers to time base selected
[HH:MM or MM:SS] - see “SP.
Pr” parameter in
“Hrd” menu)
“S” step hold time (time set
refers to time base selected
[HH:MM or MM:SS)
Defines “S” step type. Hold Back Band (HBB)
function; lets you disable HBB during
a segment or entire step.
Parameter is ON if HBB is enabled
(see “SP.Pr” parameter on “Hrd” menu)
Sty HBB enabled
HBB enabled
HBB referred to PV
for ramp
for hold
or auxiliary input
0
PV
1
x
PV
2
x
PV
3
x
x
PV
4
aux. input
5
x
aux. input
6
x
aux. input
7
x
x
aux. input
“S” step ramp
events
Eu.r
o Event 1 Event 2 Event 3 Event 4
Eu.S
0 OFF OFF OFF OFF
1 ON OFF OFF OFF
2
OFF
ON
OFF
OFF
3
ON
ON
OFF
OFF
4 OFF OFF ON OFF
5 ON OFF ON OFF
6
OFF
ON
ON
OFF
7
ON
ON
ON
OFF
8
OFF
OFF
OFF
ON
9
ON
OFF
OFF
ON
10
OFF ON OFF ON
11 ON ON OFF ON
12
OFF
OFF
ON
ON
13
ON
OFF
ON
ON
14
OFF ON ON ON
15
ON ON ON ON
“S” step hold
events
Step “S” advanced through digital input function.
When digital inputs have state set in this function, program
automatically advances to next step, otherwise it “waits” at
end of previous step (function is enabled through “SP.Pr”
parameter on “Hrd” menu);
“d.i.F.1” and/or “d.i.F.2” set to 12.
Hold Back Band value,
symmetrical to active setpoint.
Available if enabled (see “SP.Pr” parameter on
“Hrd” menu); can be disabled during a program
segment ( see “Sty” parameter).
+ 8 to enable slave setpoint ramp
INFO
Serial
communication
code
Software
version
Software
protection
code
Self diagnostic
error code
8
9
10
11
12
Information
display
0 No Error
1 Lo
2 Hi
3 ERR
4 SBR
• InFo Display
222
223
224
226
227
228
229
230
232
233
234
235
GrP.
Selection of a control
parameter group
during ramp phases
and holding of setpoint
programmer.
242
GrP.
Ramp
Hold
group
group
0
0
0
1
0
1
2
0
2
3
0
3
4
1
0
5
1
1
6
1
2
7
1
3
8
2
0
9
2
1
10
2
2
11
2
3
12
3
0
13
3
1
14
3
2
15
3
3
Sl.s
0.0 ... 100.0%
retransmitted
output value
Setpoint slaved to step “S”,
for second external channel
(to be retransmitted to a slave
controller); available if enabled
(see “SP.Pr” parameter on
“Hrd” menu)
231
0 ... 3
C.GrP
Selection of a control
parameter group
to be set.
Proportional band for
heating or hysteresis for
ON/OFF control
0.0 ... 999.9%
full scale
243
244
Integral time
for heating
0.00 ... 99.99 min
245
Derivative time
for heating
0.00 ... 99.99 min
246
Maximum power limit
for heating
0.0 ... 100.0%
247
h.
P.Lo
Minimum power limit for
heating (not available for
double heat/cool action)
0.0 ... 100.0%
248
+ 16 to force the power limit of group 0 when in “hold” phase
h.
P.xi
4
80090G_MHW_1600-1800P_04-2013_ENG
