Gefen GEF-DVI-16416 Скачать руководство пользователя страница 76

Страница: 76 / 80

SPECIFICATIONS

Video Amplifier Bandwidth ........................................................................................ 165 MHz

Single Link Range ................................................................................................1920 x 1200

Input Video Signal ................................................................................................1.2 Volts p-p

IR Extender................................................................................................3.5 mm mini-stereo

RS-232 Interface........................................................................................DB-9 serial, female

DVI Connector .................................................................... DVI-I 29-pin, female (digital only)

Power Supply...................................................................................................100 ~ 240 V AC

Power Consumption ........................................................................................90 Watts (max.)

Operating Temperature................................................................ +32 to +104 ˚F (0 to +40 ˚C)

Storage Temperature................................................................... -4 to +140 ˚F (-20 to +60 ˚C)

Relative Humidity..................................................................20 to 90% RH (no condensation)

Dimensions (W x H x D) ................................17.25’’ x 3.5” x 12” (438mm x 89mm x 305mm)

Rack-mountable ............................................................................................... 2U rack space

Shipping Weight ........................................................................................28.1 lbs. (12.75 kg)

Содержание GEF-DVI-16416

















































































Результаты поиска

Содержание GEF-DVI-16416

Отзывы:

Бренды по названию

Популярные бренды

Gefen GEF-DVI-16416, Руководство пользователя

Результаты поиска

Содержание GEF-DVI-16416

Отзывы:

Бренды по названию

Популярные бренды