Gefen GEF-DVI-16416 Скачать руководство пользователя страница 6

Страница: 6 / 80

READ THESE NOTES BEFORE INSTALLING OR

OPERATING THE GEFENPRO 16X16 DVI MATRIX

•

The GefenPRO 16x16 DVI Matrix does not support HDCP content.

•

Make sure that a DVI monitor is powered and connected to one of the DVI outputs on

the GefenPRO 16x16 DVI Matrix before applying power. By default, the Local EDID

is read from the connected monitor and is copied to all 16 DVI inputs once the Matrix

has been turned on. If a monitor is not detected by the Matrix at power-on, a default

(internal) EDID of 640x480 will be used. This functionality can be disabled / enabled

by using the

#lock_edid

command through RS-232, Telnet, UDP, or using the Web

interface. See page 19 for more information.

•

There is no internal scaling in the GefenPRO 16x16 DVI Matrix. Each monitor

attached to the Matrix must be able to display the resolutions output by the source

device(s). For maximum compatibility it is recommended that only one common

resolution be used by each source device.

•

Advanced EDID features and IP configuration features are accessible through the

RS-232 serial command set.

•

Routing and EDID features can be managed using the built-in IP control feature.

•

The Gefen Firmware Upgrade Tool is a free downloadable application from Gefen that

provides automatic download and installation of firmware upgrades for this product.

See page 60 for more information.

•

The Gefen Matrix Switcher Keyboard Controller is a free downloadable application

from Gefen that allows a computer keyboard to be used to switch between sources.

This application uses the Telnet protocol to control any Gefen switcher or matrix that

uses IP control.

Download the application here:

http://www.gefen.com/support/download.jsp

OPERATION NOTES

IMPORTANT:

If the unit is installed in a closed or multi-rack

assembly, do not block the ventilation holes of the enclosure.

Содержание GEF-DVI-16416

















































































Результаты поиска

Содержание GEF-DVI-16416

Отзывы:

Бренды по названию

Популярные бренды

Gefen GEF-DVI-16416, Руководство пользователя

Результаты поиска

Содержание GEF-DVI-16416

Отзывы:

Бренды по названию

Популярные бренды