For additional technical assistance, call 800/TEC-TRUE (800-832-8783) or visit our website at chicagofaucets.com.
6
Replacing Battery
A traditional lavatory faucet is shown as an example. These instructions apply to all DC and EBPS models.
Prerequisites
• Battery is low (LED is lit)
• New 6 V Lithium battery (CR-P2) is required
• NOTE: For EBPS units, low battery LED will only light when AC power is disconnected
1. Remove shut-off screw
2. Remove mixer handle
(for faucets with external
mixer only)
3. Remove housing
vertically
4. Remove used battery
from holder and recycle
5. Insert new battery.
IMPORTANT: be sure
battery is fully seated.
LED will illuminate when
battery is properly
installed.
6. Mount housing vertically
7. Install shut-off screw
8. Install mixer handle
(for faucets with external
mixer only)
The battery is now
replaced.
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
9
Mount mixer handle (only for faucets with
external mixer)
Result
The "Manual Setting" Mode is now enabled.
A - Setting Cleaning Mode
Setting the cleaning mode will make the faucet inactive for
90 seconds.
1
2
Fully cover sensor with hand, until water flow stops.
(This takes 5 seconds)
Result
B - Setting Normal Mode
Setting the normal mode will allow the faucet to activate only
when it senses a hand presence.
1
Enable "Manual Setting" Mode
2
2
Enable "Manual Setting" Mode
> see "Enabling Manual Setting Mode" section
3
Remove hand
The Cleaning Mode is now active. For the next 90 seconds,
the faucet will
be inactive.
3
Remove hand
Result
Metering Mode is now activated for 10 seconds.
1
Enable "Manual Setting" Mode
> see "Enabling Manual Setting Mode" section
Fully cover sensor with hand. Water flow stops
after 5 seconds - Continue to hold on for
another two (2) additional water pulse
C - Setting Metering
Mode (10 seconds)
Setting the metering mode will allow the faucet to activate for
a full 10 seconds after it senses a hand presence.
3
Remove hand
Result
Normal Mode is now activated.
> see "Enabling Manual Setting Mode" section
Fully cover sensor with hand. Water flow stops after
5 seconds - Continue to hold on for one (1) additional
water pulse
Adjusting Water Temperature (Internal Mix)
A traditional lavatory faucet is shown as an example. These instructions apply to all models with internal mixers.
1. Remove shut-off screw
2. Remove housing
vertically
3. Adjust internal mixer with
screwdriver
Clockwise > warm
Counterclockwise < cold
4. Mount housing vertically
5. Install shut-off screw
The temperature is now
adjusted. Carefully test
the new temperature. If
necessary, adjust again.
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
Result
The battery is now replaced.
3
5
+
-
7
Install shut-off screw
8
Install mixer handle (for faucets with external mixer only)
Cleaning or Replacing Inlet Filter
1
Close supply valves
2
Disconnect braided hoses and clean or replace filter
(for a new filter, see "common replacement parts" )
Connect braided hoses with filter to supply valves and
fully open.
Cold water > white label
Warm water > no label
Result
The filter is now cleaned or replaced.
3
Adjust internal mixer with screwdriver
Clockwise > warm
Counterclockwise > cold
4
Mount housing vertically
Adjusting Water Temperature (Internal Mixer)
A traditional lavatory faucet is shown as an example. These
instructions apply to all models with internal mixers.
1
Remove shut-off screw
2
Remove housing vertically
Adjusting Hot Water Limiter (External Mixer)
A traditional lavatory faucet is shown as an example. These instructions apply to all models with user adjustable temperature control. The proportion
of hot water can be switched from approximately 85% to 95% (or reverse) depending upon inlet water pressures and temperatures. The default setting
is 85%.
HyTronic
®
User Guide Installation Instructions
(continued)
Enabling "Manual Setting" Mode
A battery model is shown in the following example. These
instructions apply to all models. After 30 minutes, the
"Manual Setting" mode will be disabled automatically and
all settings will be saved.
Prerequisites
• Water supply valve is open
• Battery is full (LED does
not blink) for DC faucets
• AC power is on for AC faucets
1
Remove shut-off screw
2
Remove mixer handle (only for faucets with
external mixer)
3
Remove housing vertically
4
Remove battery from battery holder
5
The following procedure (a, b, c) must be done three (3)
times in a row.
a - Re-insert battery
b - LED lights up
c - Remove battery immediately after LED switches off
6
Insert battery
7
Mount housing vertically
8
Mount shut-off screw
a
c
b
9
Mount mixer handle (only for faucets with
external mixer)
Result
The "Manual Setting" Mode is now enabled.
A - Setting Cleaning Mode
Setting the cleaning mode will make the faucet inactive for
90 seconds.
1
2
Fully cover sensor with hand, until water flow stops.
(This takes 5 seconds)
Result
B - Setting Normal Mode
Setting the normal mode will allow the faucet to activate only
when it senses a hand presence.
1
Enable "Manual Setting" Mode
2
2
Enable "Manual Setting" Mode
> see "Enabling Manual Setting Mode" section
3
Remove hand
The Cleaning Mode is now active. For the next 90 seconds,
the faucet will
be inactive.
3
Remove hand
Result
Metering Mode is now activated for 10 seconds.
1
Enable "Manual Setting" Mode
> see "Enabling Manual Setting Mode" section
Fully cover sensor with hand. Water flow stops
after 5 seconds - Continue to hold on for
another two (2) additional water pulse
C - Setting Metering
Mode (10 seconds)
Setting the metering mode will allow the faucet to activate for
a full 10 seconds after it senses a hand presence.
3
Remove hand
Result
Normal Mode is now activated.
> see "Enabling Manual Setting Mode" section
Fully cover sensor with hand. Water flow stops after
5 seconds - Continue to hold on for one (1) additional
water pulse
1. Remove mixer handle
2. Carefully pull out hot
water limiter from handle
(using pliers) and reverse
by 180°
Settings of hot water limiter
(View from placement in
mixer handle)
3. Mount mixer handle
The proportion of hot water
is now changed.
5
A traditional lavatory faucet is shown as an example. These
Warning
Hot water may burn your skin
Hold hand carefully and quickly under water
Settings of hot water limiter
(View from placement in mixer handle)
180°
95%
85%
Cleaning or Replacing Outlet
1
Remove shut-off screw
Result
The outlet is now cleaned or replaced.
Install shut-off screw
Result
The temperature is now adjusted.
Carefully test the new temperature. If necessary, adjust again
Adjusting Hot Water Limiter (External Mixer)
instructions apply to all models with external mixers. The
proportion of hot water can be witched from approximately
85% to 95% (or reverse) depending upon inlet water
pressures and temperatures. The default setting is 85%.
1
Remove mixer handle
2
Carefully pull out hot water limiter from handle
(using pliers) and reverse by 180°
3
Install shut-off screw
2
Remove outlet with vandal
resistant wrench supplied
with the faucet. Clean or replace outlet, then reinstall
Result
The proportion of hot water is now changed.
3
Mount mixer handle
5
A traditional lavatory faucet is shown as an example. These
Warning
Hot water may burn your skin
Hold hand carefully and quickly under water
Settings of hot water limiter
(View from placement in mixer handle)
180°
95%
85%
Cleaning or Replacing Outlet
1
Remove shut-off screw
Result
The outlet is now cleaned or replaced.
Install shut-off screw
Result
The temperature is now adjusted.
Carefully test the new temperature. If necessary, adjust again
Adjusting Hot Water Limiter (External Mixer)
instructions apply to all models with external mixers. The
proportion of hot water can be witched from approximately
85% to 95% (or reverse) depending upon inlet water
pressures and temperatures. The default setting is 85%.
1
Remove mixer handle
2
Carefully pull out hot water limiter from handle
(using pliers) and reverse by 180°
3
Install shut-off screw
2
Remove outlet with vandal
resistant wrench supplied
with the faucet. Clean or replace outlet, then reinstall
Result
The proportion of hot water is now changed.
3
Mount mixer handle
WARNING: Hot water
may burn your skin.
To avoid the risk
of scalding, use a
thermometer to check
water temperature.
Avoid contact with the
water stream until the
water temperature has
been properly adjusted.
CARE AND MAINTENANCE INSTRUCTIONS
