background image

 

 

VersaMax*  

 

IC200BEM003 

GFK-2739  

 

PROFIBUS Master Module

 

April 2012 

 

The VersaMax

*

 IC200BEM003 PROFIBUS Master Module allows a VersaMax 

CPU005, CPUE05 or PROFINET Scanner (PNS) to send and receive data on a 
PROFIBUS-DP V1 network.  

The PROFIBUS Master module provides the following PROFIBUS 
communications features: 

 

Supports all standard data rates  

 

Supports a maximum of 3,584 bytes of input data and 3,584 bytes of output 
data with a VersaMax CPU; a maximum of 1440 bytes of input data and 1440 
bytes of output data with a PNS. 

 

Supports a maximum of 125 PROFIBUS-DP slaves, with a maximum of 244 
bytes of input data and 244 bytes of output data for each slave 

 

Supports Sync and Freeze modes  

 

Supports DP-V1 Read, Write and Alarm messages 

 

Has PROFIBUS-compliant module and network status LEDs 

This module must be located in a VersaMax Communications Carrier. 

The PROFIBUS module receives its firmware upgrades indirectly from the 
head end CPU or PNS using the WinLoader software utility. WinLoader is 
supplied with any updates to the PROFIBUS module software. 

Ordering Information 

IC200BEM003 

VersaMax PROFIBUS Master Module 

IC200CHS006 

VersaMax Communications Carrier 

 

 

Specifications 

PROFIBUS support 

PROFIBUS-DP V1 

Power Consumption 

450mA at +5V 

I/O Data  

 

 

With a CPU

 

A maximum of 3584 bytes of input data and 3584 bytes of output data 

 

With a PNS

 

A maximum of 1440 bytes of input data and 1440 bytes of output data 

 

With either CPU or PNS head end, a maximum of 244 bytes of input data and 244 
bytes of output data for each slave. 

PROFIBUS network addresses 

0 to 125, software-configurable 

Maximum no. of slave devices 

125 

Network data rate 

9.6K up to 12 Mbaud (bit/sec) 

Status information 

Slave Status Bit Array Table 
Firmware Module Revision 
Slave Diagnostic Address 

Module isolation 

Network to Frame ground: 250VAC continuous, 1500VAC for 1 min 
Profibus network to backplane: 1500VAC minimum 

For product standards, general operating specifications, and installation requirements, refer to the 

VersaMax I/O Modules 

Manual

, GFK-1504. 

                                                           

*

 

indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates.  All other trademarks are the property 

of their respective owners.

 

Содержание VersaMax IC200BEM003






Отзывы: