GE SymVeo SV-XP1 Скачать руководство пользователя страница 55

Страница: 55 / 60

Firmware upgrades

To properly upgrade the IP Camera, the following conditions
must exist:

1. You must have the flash upgrade file. You can obtain this

file by contacting GE Security Technical Support. (See

Contacting technical support

on page 53.) When calling,

please have the following information available:

•

the model number of the product;

•

the serial number and revision of the product;

•

the current firmware version;

•

the date purchased; and

•

The reason you wish to upgrade the firmware.

2. The SymVeo IP camera unit must be connected to a PC

equipped with Microsoft Internet Explorer version 5.5 or
later via an ethernet cable.

3. You must know the IP address of the IP Camera.

4. You must exit all nonessential software on the PC.

Содержание SymVeo SV-XP1





























































Результаты поиска

Содержание SymVeo SV-XP1

Отзывы:

Похожие инструкции для SymVeo SV-XP1

Бренды по названию

Популярные бренды

GE SymVeo SV-XP1, Руководство пользователя

Результаты поиска

Содержание SymVeo SV-XP1

Отзывы:

Похожие инструкции для SymVeo SV-XP1

Бренды по названию

Популярные бренды