manualshive.com logo in svg

GE PACSystems RXi Box IPC, Руководство пользователя

Поделиться
Скачать
GE PACSystems RXi Box IPC Скачать руководство пользователя страница 31

Connectors and Cabling 

 26 

PACSystems* RXi Box IPC 

GFK-2785C

 

Ethernet Communication Ports 

The IPC provides two RJ-45 Ethernet network port 
connectors that support 10BASE-T, 100BASE-TX and 
1000BASE-T communications. Either or both of these ports 
may be attached to other Ethernet devices. Each port 
automatically senses the data rate (10, 100 or 1000Mbps), 
duplex (half duplex or full duplex), and cabling 
arrangement (straight through or crossover) of the 
attached link. 

Caution 

The two ports on the Ethernet Interface must not be connected, directly or 
indirectly to the same device. The hub or switch connections in an Ethernet 
network must form a tree, otherwise duplication of packets may result. 

Ethernet Media 

The IPC can operate on 10BASE-T, 100BASE-TX or 1000BASE-T media via its network ports. All 
three arrangements can use up to 100m of twisted pair cable between each node and a switch, 
hub, or repeater. 

Note:

 

For all three types, shielded twisted pair (STP) cable is required to maintain 
CE compliance. 

10BASE-T:

 Two pairs of wire are used, one for transmission, and the other for receive. 

100BASE-TX:

 Two pairs of wire are used, one for transmission, and the other for receive. 

1000BASE-T: 

Four pairs of wire are used for simultaneous transmission and receive in both 

directions. 

Ethernet Port Pin Assignments 

Pin No. 

10BASE-T/100BASE-TX 

1000BASE-T 

Signal 

Description 

Signal 

Description 

1 

TD+ 

Transmit Data + 

BI_DA+ 

Bidirectional pair A+ 

2 

TD- 

Transmit Data – 

BI_DA- 

Bidirectional pair A- 

3 

RD+ 

Receive Data + 

BI_DB+ 

Bidirectional pair B+ 

4 

NC 

no connection 

BI_DC+ 

Bidirectional pair C+ 

5 

NC 

no connection 

BI_DC- 

Bidirectional pair C- 

6 

RD- 

Receive Data – 

BI_DB- 

Bidirectional pair B- 

7 

NC 

no connection 

BI-DD+ 

Bidirectional pair D+ 

8 

NC 

no connection 

BI_DD- 

Bidirectional pair D- 

Note:

 

Pin assignments are provided for diagnostic purposes only. Ethernet cables are readily 
available from commercial distributors. We recommend purchasing rather than making 
cables. 

The operation of the Ethernet port LED indicators, 

ACTIVITY

 and 

LINK

, is described in chapter 1. 

Pin 1 

ACTIVITY 
LED 

LINK 
LED 

Содержание PACSystems RXi Box IPC













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды