background image

Stay Light 

The  stay light is “on” when the all interior (motion detector) zones are 
bypassed. 

Zone Light  

The zone lights are “off” when everything is normal. A zone light will be “on” if 
the zone has been bypassed. If a zone light is “flashing”, that zone is in alarm 
or has been faulted. If a zone light is “flashing” rapidly, it means that the zone is 
in a trouble condition.   Trouble conditions are: 

 

Tamper 

 

Hardware 

 

Low Battery 

 

Loss of Supervision 

(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid 
“flashing” light for a short period of time, followed by a slow “flashing” light.) 

 

EMERGENCY ACTIVATION KEYS 

 
NOTES: You must press and hold these keys for 2 seconds to activate 
these functions.   Your system may not be programmed for these activation 
keys (see page 1)
You should press these keys only in an emergency situation 
that requires response by emergency personnel.   If your system is programmed 
for these functions, the following reports can be sent. 
 
Fire Key
 – This key can activate the fire alarm when pressed for two seconds. If 
your system is connected to a monitoring center, an emergency report could be 
sent to that center. The keypads sound a continuous beeping. 
 
Auxiliary Emergency Key
 – This key can activate the auxiliary alarm when 
pressed for two seconds. If your system is connected to a monitoring center, an 
emergency report could be sent to that center.  The keypads sound a continuous 
beeping. 
 
Police (Panic/Hold-Up) Key
 - This key can sound a local audible alarm when 
pressed for two seconds. If your system is connected to a monitoring center, an 
emergency report could be transmitted to that center.  NOTE: Some Panic/Hold-
Up alarms are programmed to be silent at the protected site while reporting an 
alarm to the monitoring center. Check with your installing company to determine 
how your security system will respond to the Panic/Hold-Up activation. If 
programmed for Silent Hold-up, the keypads will not sound. Otherwise, the 
keypads will sound a continuous beeping. 

Содержание NX-108E - Security NetworX NX-4 System





















Отзывы: