manualshive.com logo in svg

GE MG-101, Руководство пользователя

Поделиться
Скачать
GE MG-101 Скачать руководство пользователя страница 5

MG-101 User’s Manual

iii

Preface

Information Paragraphs

•

Note

 paragraphs provide information that provides a deeper understanding of the situation, but is not essential to 

the proper completion of the instructions.

•

Important

 paragraphs provide information that emphasizes instructions that are essential to proper setup of the 

equipment. Failure to follow these instructions carefully may cause unreliable performance.

•

Caution!

 paragraphs provide information that alerts the operator to a hazardous situation that can cause damage to 

property or equipment.

•

Warning!

 paragraphs provide information that alerts the operator to a hazardous situation that can cause injury to 

personnel. Cautionary information is also included, when applicable.

Safety Issues

WARNING! It is the responsibility of the user to make sure all local, county, state and national codes, 

regulations, rules and laws related to safety and safe operating conditions are met for each 
installation.

Auxiliary Equipment

Local Safety Standards

The user must make sure that he operates all auxiliary equipment in accordance with local codes, standards, 
regulations, or laws applicable to safety.

Working Area

WARNING! Auxiliary equipment may have both manual and automatic modes of operation. As equipment 

can move suddenly and without warning, do not enter the work cell of this equipment during 
automatic operation, and do not enter the work envelope of this equipment during manual 
operation. If you do, serious injury can result.

WARNING! Make sure that power to the auxiliary equipment is turned OFF and locked out before you 

perform maintenance procedures on the equipment.

Qualification of Personnel

Make sure that all personnel have manufacturer-approved training applicable to the auxiliary equipment.

Personal Safety Equipment

Make sure that operators and maintenance personnel have all safety equipment applicable to the auxiliary equipment. 
Examples include safety glasses, protective headgear, safety shoes, etc.

Unauthorized Operation

Make sure that unauthorized personnel cannot gain access to the operation of the equipment.

Содержание MG-101



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды