manualshive.com logo in svg

GE MG-101, Руководство пользователя

Поделиться
Скачать
GE MG-101 Скачать руководство пользователя страница 16

Chapter 2. Setup and Operation

8

MG-101 User’s Manuall

2.2 Operating Procedure

To operate the MG-101, refer to 

Figure 5

 below and 

Figure 6 on page 9

 to complete the following steps:

1.

Fully close

 all four rotameter valves by turning them clockwise.

2.

Set the 

WET/DRY

 selector valve to 

DRY

.

CAUTION!

This valve must always be in the WET position before the “WET GAS” flowmeter valve is opened, 
and it must remain in the DRY position until the “WET GAS” flowmeter valve is closed.

3.

Set the pressure regulator on the nitrogen gas inlet line to approximately 55 psig.

4.

Make sure the vent valve at the top of the front panel is 

fully

 open.

5.

Fully

 open the valve on the 

WET GAS DILUTED

 rotameter.

Note:

The rotameters are dual-range, floating-ball types, each having both a steel ball and a glass ball. When 
reading the rotameters be careful to watch either the steel ball or the glass ball (see Figure 4 below) as 
directed (numbers in tables are followed by an 

S

 or a 

G

 to designate the ball material).

Figure 5: Rotameter Valve and Balls

Glass Ball (black)

Steel Ball (silver)

Valve

Содержание MG-101



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды