Guide
before touching or
Part
Materials to Use
General Directions
Tub
●
Hot Soapy Water
Wipe clean after each use. Make sure drain hole is not blocked. Use cotton swab
or
●
Soap-Filled Scouring Pad
toothpick to clean drain hole.
Plastic Scouring Ball
Reflector Pan
●
Hot Soapy Water
Let grill cool. Remove
heating unit and
out Reflector Pan.
●
Soap-Filled Scouring Pad
Reflector Pan may be cleaned using one of the methods at left.
●
Plastic Scouring Ball
Can be cleaned in dishwasher.
●
Dishwasher Safe
Grease Collector Jar
●
Hot Soapy Water
Scoop out grease with large spoon. Set jar in pan of warm water to loosen grease if
●
Scouring
desired. Replace with any wide mouth canning jar. Do not use a mayonnaise jar
●
Plastic Scouring Pad
which could break when hot grease drips into it.
●
Dishwasher Safe
Grill Grate
●
Hot Soapy Water
Do not clean in a self-cleaning
oven.
●
Plastic Scouring Ball
Can be cleaned in dishwasher.
●
Dishwasher Safe
Griddle
●
Hot Soapy Water
Do not use abrasive cleaners.
●
DO
wash in dishwasher.
. Plastic Scouring
Control Knobs
●
Soap and Warm Water
Pull off knobs. Wash gently but do not soak. Dry and return controls to
making sure to match flat area on the knob and shaft.
Control Panel
●
Soap and Water
Wash with cloth dampened in soapy water. Rinse and polish with a dry
cloth. If knobs on the control panel are removed, do not allow water to run down
inside the surface of control panel while cleaning.
Surface
●
Hot Soapy Water
Wash, rinse, and then polish with a dry cloth. DO NOT USE
steel wool, abrasives,
ammonia, acids, or commercial oven cleaners which may damage the finish.
Aluminum
. Hot Soapy Water
Wipe
drip pans after each cooking so spatter will not “bum on” next time you
Surface Unit
●
Stiff-Bristled Brush
Drip Pans
cook. To remove “burned-on” spatters, use any or
cleaning materials
●
Soap-Filled Scouring Pad
mentioned. Rub
lightly
with scouring pad to prevent scratching of the surface.
●
Dishwasher Safe
Can be cleaned in the dishwasher.
Will discolor if cleaned in self-cleaning oven.
Chrome-Plated
●
Hot Soapy Water
Wipe trim rings after cooking so spatters will not “burn on” the next time
Rings
●
Dishwasher Safe
cook.
Can be cleaned in the dishwasher.
DO
clean trim rings in a self-cleaning oven.
Surface Unit Coils
●
None Required
Spatters and spills burn away when the coils are heated. At the end of a meal,
and
Heating
Unit
remove all pans from the surface units and heat the soiled units at HIGH. Let the
soil burn off about a minute and switch the units to OFF. Avoid getting cleaning
materials on the coils. Wipe off any cleaning materials with a damp paper towel
before
heating the surface unit.
DO
handle the unit before completely cooled.
DO NOT clean plug-in units in a self-clean oven.
DO NOT immerse plug-in units in any kind of liquid or clean in dishwasher.
Solid Disk Elements
●
Soap and Water
The solid disk elements should be washed with a damp cloth and then dried. Finish
and
●
Cleansing Powder
by wiping over
with cooking oil when cool. Clean very dirty solid disk
11’” element
●
Soap-Filled Scouring Pad
elements with a little cleaning powder or a scouring pad. Do not scour the center
(on models
●
Cello
Polish
sensing device on the
element. The matte black surface can be
maintained by treating it periodically with the Cello
polish. It is available
from your GE supplier. To use the finish, use the applicator to apply a very thin
coating of the polish to the entire element surface.
the element on high for
several minutes to bake the polish to the element. When the element is cool, rub
with a cloth or paper towel to remove any excess polish.
Solid Disk Module
●
Hot Soapy Water
Clean the brushed chrome finish and the
steel trim ring that surrounds the
●
Soft Sponge
solid disk element by following the directions below.
●
Cloth
For light soil, wash and rinse with soapy water and then polish with a dry cloth.
For heavy soil,
baking soda on soiled area. Cover with a moist cloth or
paper towel and allow to set for at least 30 minutes. Then wipe up the baking soda,
rinse with a damp cloth and polish with a dry cloth. DO
USE steel wool or
abrasives on the
disk module or elements.
