GE H301 Series Скачать руководство пользователя страница 58

Страница: 58 / 137

48 | Chapter 4: Installation

6. Verify the hold down bolting torque and soft foot checks quarterly. See the

"Quarterly maintenance checklist"

Piping

Process gas Piping

Install all compressor suction and discharge process gas piping as follows:

1. The suction and discharge piping should never be smaller than the

compressor suction and discharge pipe flange connections.

The only exception to this minimum piping size requirement is

specifically designed choke tubes.

Complies with ANSI Z535, ISO 3864, OSHA 1910.145 (f) (9)

2. All piping should be thoroughly cleaned internally of weld slag, mill scale, and

other construction debris before installation.

3. Avoid using a skid or underground inlet piping loops that can trap liquids

(“pee” trap affect). Liquids can accumulate, with resulting liquid carry over into

scrubbers and cylinders. This can result in major damage to the scrubber and
the internals of the compressor cylinder.

4. Install an inlet gas scrubber(s), whenever wet or dirty gas is being compressed,

on the suction lines to each 1st stage or side stream stages .

5. Piping should be connected to the compressor strain free, in such a way that

undue thermal or mechanical stresses are placed on the compressor.

6. Install liquid separators, with ample capacity and drainage, to remove the

condensate in the piping leaving the coolers. Also, install drain valves in all
“low spots” in the piping.

7. Design and install the inlet piping to all cylinders so that no incompressible

materials (dirt, liquids or foreign materials) can enter the compressor. During

the first few weeks of operation, a temporary inlet strainer, similar to that

shown in

"Figure 10"

, can be installed.

8. All cylinder bottle supports must be “loose” when “cold” and no adjustments

should be made until the compressor has warmed up. The cylinder and
crosshead guide bores should be level and not distorted when the bottle

supports are correctly adjusted. Make the final bottle support adjustment

when the compressor cylinders have reached their normal (hot) operating
temperatures.

Содержание H301 Series










































































































































Результаты поиска

Содержание H301 Series

Отзывы:

Похожие инструкции для H301 Series

Бренды по названию

Популярные бренды

GE H301 Series, Руководство по эксплуатации

Результаты поиска

Содержание H301 Series

Отзывы:

Похожие инструкции для H301 Series

Бренды по названию

Популярные бренды