8
49-3000346 Rev 0
Getting started
USING THE W
A
SHER
Start/Pause
Press
Start
to begin the cycle.
NOTE:
Unless
Bulky Items
cycle is selected, the lid must be closed for the washer to start cycle.
If the lid is open, “Lid” will scroll across the display. During the load sensing portion of the cycle, the lid will lock and “SEnSing” will
scroll across the display. When load sensing is complete, the lid will unlock.
Pressing
Pause
will unlock the lid (if locked at that time), pause the cycle and the
Start
indicator light will blink.
To continue the cycle, press
Start
again. If water remains in the machine, select the
Drain & Spin
cycle to drain basket and
spin water out of the washer basket.
NOTE:
Machine will automatically cancel and drain when water is present and the lid is
left open for 15 minutes or the unit is left in a paused state for 24 hours with the lid closed. Select cycle and press
Start
to
begin new cycle.
Display
and Status Lights
Display:
The display shows the
approximate
time remaining until the end of the cycle.
NOTE:
The cycle time is affected by
how long it takes the washer to fill. This depends on the water pressure in your home. The size of the load being washed also
significantly impacts cycle time, with larger loads taking longer.
In addition, this display will, “scroll” the washer status:
• bALAnCINg
Start of rebalancing cycle to redistribute clothes. Stops after rebalancing is complete.
• dELAY
When
Delay Wash
is initiated. Replaced with estimated time when cycle starts.
• End
End of current cycle.
• FILL
“FILL” will scroll across display for the first 45 seconds of fill, afterwards the estimated end of cycle time is
displayed.
• H2O SUPPLY
Can not sense water level (valves possibly turned off).
• LId
Cycle stopped because lid is open. Close the lid.
• SEnSIng
Sensing load size and type before and during fill (normal).
• PAUSE
Cycle paused because the
Start
/
Pause
button was pressed and the washer was set to
Pause
. Press
Start
button again to restart the cycle.
Cycle status lights:
Shows whether the washer is in the
Delay
,
Fill
,
Soak (on some models)
,
Wash, Rinse
or
Spin
portion of the cycle.
If an out-of-balance condition is detected by the washer, the
Spin
light will blink during the remaining portion of the cycle
and will stay illuminated for a short time after cycle completion. When this occurs, the washer is taking actions to correct the
out-of-balance condition and complete the cycle normally. In some cases, the washer may not be able to balance the load
and spin up to full speed. If you notice the load is more wet than normal at the end of the cycle, redistribute the load evenly
in the wash basket and run a
Drain & Spin
cycle.
C
B
Feature status lights indicate
(see sections
F
and
G
for more details):
Pause
- Will display when washer is paused between cycles.
Controls
- The washer is locked - will blink once if you press any button or turn the cycle knob.
Lid Lock
- The lid is locked. See the
Control Lock
description.
WiFi
(on some models) - Will display when washer is connected via WiFi. Will blink when you are attempting to connect
your device to your home WiFi.
Spin Stop
- Indicates wash basket is coasting to a stop following spin. Lid will not unlock until basket has fully come to a stop.
A
Power
Press to “wake up” the display. If the display is active, press to put the washer into idle mode.
NOTE:
Pressing
Power
does not disconnect the appliance from the power supply.
Содержание GTW685
Страница 3: ...49 3000346 Rev 0 3 WELCOME Notes...
Страница 17: ...49 3000346 Rev 0 17 NOTES Notes...
Страница 33: ...49 3000346 Rev 0 3 BIENVENIDO Notas...
Страница 47: ...49 3000346 Rev 0 17 NOTAS Notas...