background image

7

Installation Instructions

3-WIRE CONDUIT INSTALLATION

Loosen the 3 lower terminal screws from
the terminal block. Insert the center bare
wire (white/neutral) tip through the bottom
center terminal block opening. On certain
models, the wire will need to be inserted
through the ground strap opening and then
into the bottom center block opening. Insert
the two side bare wire tips into the lower
left and the lower right terminal block
openings. Tighten the screws until the wire
is firmly secured (35 to 50 inch-lbs.). Do not
over-tighten the screws since it could
damage the wires.

NOTE: ALUMINUM WIRING:

Aluminum building wire may be used
but it must be rated for the correct
amperage and voltage to make
connection. Connect wires according 
to this Step 6 or Step 7 depending on
number of wires.

Wire used, location and enclosure 
of splices, etc., must conform to good
wiring practices and local codes.

Skip to Step 8 and proceed with the
installation.

B

A

6

4-WIRE CONDUIT INSTALLATION

Loosen the three lower terminal screws
from the terminal block. Remove the ground
screw and ground plate and retain them. 

Cut and discard the ground strap. DO NOT
DISCARD ANY SCREWS.

Insert the ground bare wire tip between the
range frame and the ground plate (removed
earlier) and secure it in place with the ground
screw (removed earlier). Insert the bare wire
(white/neutral) tip through the bottom center
of the terminal block opening. Insert the two
side bare wire tips into the lower left and the
lower right terminal block openings. Tighten
the screws until the wire is firmly secured
(35 to 50 inch-lbs.). Do not over-tighten the
screws since it could damage the wires.

Wire used, location and enclosure 
of splices, etc., must conform to good
wiring practices and local codes.

Proceed to Step 8.

C

B

A

7

Before

Terminal
block

Ground strap

After

Terminal
block

Ground
plate
(grounding
to range)

Bracket

Neutral
terminal

Wire tips

Wire tips

Terminal
block

Conduit

Bracket

Ground
screw

Ground strap 

or

Содержание Free-Standing Ranges













Отзывы: