manualshive.com logo in svg

GE EntelliGuard R7, Руководство по установке

GE EntelliGuard R7 - мощный и надежный магнитный пускатель с возможностью удаленного управления. Установите его с помощью подробной инструкции по монтажу, которую вы можете бесплатно скачать с нашего сайта. Посетите manualshive.com, чтобы скачать руководство пользователя прямо сейчас.

Поделиться
Скачать
background image

 

24  

EntelliGuard R Circuit Breaker Retrofill AKD-10 Installation Manual         DEH41550 R06   

 

Install AKD-10 & substructure type 3200, 4000 & 5000A Retrofill Breaker

. 

To remove the exiting breaker follow instructions provide with the legacy breaker and or switchgear/ 
switchboard.  Note that one must remove the two ½-13 bolts holding the breaker down on the drawout tray 
assembly found at the front of the tray.  Notice how the breaker is located at the rear by two pins passing 
thru the old breaker frame.  Notice how the rejection plates underneath the legacy breaker align with 
rejection pins on the drawout tray assembly.  Verify the correct breaker is being used.  Compare the rejection 
plate arrangement on the new breaker to those on the old breaker 

After the existing breaker is removed and the compartment updated with any added features, the pre-wired 
breaker can be installed in the GE AKD-10 Switchgear, GE Switchboard or OEM Equipment. 

1.

 

 Verify that the new breaker is in the disconnected and OPEN position. 

2.

 

For WPS-32/WPH-32/WPX-32/WPS-40/WPX-40/WPS-50/WPX-50 Retrofill Breaker. 
A.

 

It is best to use Lifting Bar GE Part number 

0247B8961G001

 for 3200-4000A and 

0247B8961G003

 for 5000A and a suitable hoist to lift from above as shown in Figure 12A.  (These 

lifting bars have been tested to 200% of their 700 lb ratings.) 

B.

 

Alternate method, use a lifting chain and hooks rated at least 1400 lbs to lift the breaker from 
above as shown in Figure 12B.  (chains must not be at an angle less than 45 degrees from the 
horizontal plane.)  Installation in upper compartments may not be possible with limited overhead 
space or the GE switchgear hoist. 

Figure 12. AKD-10—Location of Hooks 

Figure 12A. AKD-10—Using GE Lifting bar 
and hoist 

Figure 12B. AKD-10—Using Chain And 
Hook 

 

 

 

 

3.

 

Make sure that the lifting bar or generic  chain-hooks are secured and locked in place.  

Dropping a 

breaker can result in injury or death.

 

4.

 

Line up the breaker in front of the compartment where it will be installed; then raise it slightly above 
the height of the drawout Rail assembly. 

5.

 

Pull out the Rail assembly beneath the breaker. 

6.

 

Lower the breaker down on the Rails.  . 

7.

 

Remove the lifting bar and or chains. 

8.

 

Push the breaker into the compartment slowly while observing the alignment of the secondary 
disconnects and opening of the optional shutter.  A compartment interlock rod in the right front will 
ride over a cam and drop into position in the DISCONNECT position

. 

Содержание EntelliGuard R7





















































Отзывы:

Нет отзывов

Похожие инструкции для EntelliGuard R7

Eaton CH Instructional Leaflet preview
CH
Бренд: Eaton Страницы: 8
Eaton ETR4-70-A Instruction Leaflet preview
ETR4-70-A
Бренд: Eaton Страницы: 3
hager ZY9NK Mounting Instructions preview
ZY9NK
Бренд: hager Страницы: 2
hager HY 801, HY 802 User Instructions preview
HY 801, HY 802
Бренд: hager Страницы: 2
hager TYFS130 Assembly Instructions Manual preview
TYFS130
Бренд: hager Страницы: 6
CHINT NB7 Mounting Instructions preview
NB7
Бренд: CHINT Страницы: 6
OEZ SE-BL-1000-DTVE Instructions For Use Manual preview
SE-BL-1000-DTVE
Бренд: OEZ Страницы: 6
ABB H8304 Instructions preview
H8304
Бренд: ABB Страницы: 2
Raycap RSCAC-9556 Series Installation Instructions Manual preview
RSCAC-9556 Series
Бренд: Raycap Страницы: 12
Noark Ex9M Series Manual preview
Ex9M Series
Бренд: Noark Страницы: 55
Eaton 150 VCP-WR 1500 Instructions For The Use, Operation And Maintenance preview
150 VCP-WR 1500
Бренд: Eaton Страницы: 63
Eaton NZMB Series Instruction Leaflet preview
NZMB Series
Бренд: Eaton Страницы: 9
Eaton IZM6 Series Operating Instruction preview
IZM6 Series
Бренд: Eaton Страницы: 76
Siemens RCD310 Series Operating Instructions Manual preview
RCD310 Series
Бренд: Siemens Страницы: 12
Siemens l-T-E CMD6 Information And Instruction Manual preview
l-T-E CMD6
Бренд: Siemens Страницы: 55
Siemens NXPLUS C Installation And Operating Instructions Manual preview
NXPLUS C
Бренд: Siemens Страницы: 293
Siemens MEMOSKOP 100 SUB Service Instructions Manual preview
MEMOSKOP 100 SUB
Бренд: Siemens Страницы: 28
ABB SACE Emax 2 E2.2 Installation Instructions Manual preview
SACE Emax 2 E2.2
Бренд: ABB Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды