GE Electronic Dishwasher, Инструкция по использованию и уходу

Страница: 8 / 28

Flashing display lights (on some models)
6
Status Lights What It Means What To Do
CLEANSENSOR
Error If the sensing light doesn’t come on during the first part of the cycle,
the
CLEANSENSOR
is not working. Call for service. The dishwasher will
continue to work without the
CLEANSENSOR
.
NOTE:
This light will NOT stay on the entire cycle.
START/RESET
pad Allow up to 90 seconds for the dishwasher to drain and reset before selecting
has been pressed
a new cycle.
Control Error Press the
START/RESET
pad to turn off the beeper. Turn off power at the circuit
breaker for 10 seconds, then restore power. If the rinsing light continues to
flash, then call for service.
Control Error Press the
START/RESET
pad to turn off the beeper and the dishwasher will
attempt to reset. Then restart the wash cycle. If this error continues, call
for service.
Filling the Dispenser
Fill the rinse agent dispenser until it reaches the bottom
of lip inside the opening. Replace cap.
To check if rinse agent is needed, press the clear center
of the fill cap 2 or 3 times. If rinse agent fills the center
of the cap, you have enough.
A full dispenser should last about one month.
If rinse agent spills, wipe up the excess.
Check the Water Temperature
The entering water must be at least 120°F and
not more than 150°F for effective cleaning and to
prevent dish damage. Check the water temperature
with a candy or meat thermometer. Turn on the hot water faucet nearest the dishwasher, place
the thermometer in a glass and let the water run
continuously into the glass until the temperature
stops rising.
Use Jet-Dry ® Rinse Agent
Jet-Dry ® rinse agent removes spots and prevents new film buildup on your dishes,
glasses, flatware, cookware and plastic.
Using the dishwasher.
STATUS
SENSING
WASHING
RINSING
DRYING
SANITIZED
STATUS
SENSING
WASHING
RINSING
DRYING
SANITIZED
STATUS
SENSING
WASHING
RINSING
DRYING
SANITIZED
PLUS A
BEEPING
SOUND
STATUS
SENSING
WASHING
RINSING
DRYING
SANITIZED
PLUS A
BEEPING
SOUND
8
Lumières d’affichage
(sur certains modèles)
Affichage Signification Solution Proposée
SENSEUR
LAV AGE
RINÇAGE
SÉCHAGE
SANITISE
SENSEUR
LAV AGE
RINÇAGE
SÉCHAGE
SANITISE
SENSEUR
LAV AGE
RINÇAGE
SÉCHAGE
SANITISE
PLUS UN
SON “BIP”
SENSEUR
LAV AGE
RINÇAGE
SÉCHAGE
SANITISE
PLUS UN
SON “BIP”
Si le lumière de senseur n’allume pas
durant le cycle
NORMAL
ou
CASSEROLE. Le capteur de turbidité
est défectueux, appeler un technicien de
service. Le lave-vaisselle fonctionnera
quand même.
NOTE: Cette lumière ne reste pas
allumée durant le cycle complet.
Laisser le lave-vaisselle se vidanger et appuyer sur
touche
ANNULE
avant de sélectionner un autre
cycle.
Appuyer sur la touche
ANNULE
pour arrêter le
son. Mais la lumière RINÇAGE continuera de
clignoter. Si cela se poursuit, appeler un technicien
de service.
Appuyer sur la touche ANNULE pour arrêter le
son. Ensuite appuyer de nouveau sur la touche
MARCHE.
Si cela se poursuit, appeler un
technicien de service.
Défectuosité du capteur
turbidité
“CLEANSENSOR”
Le bouton
MARCHE /
ANNULE
a été enfoncé.
Erreur du CONTRÔLE
Erreur du CONTRÔLE
8