background image

4

 - [EN]  English

K335 Issue 3

To start - Select a task (Measure)

When the instrument is set up (Table 1), use the 

Select Task

 

menu to select the applicable task. 

In Table 2/3, P1 and P2 are internal sensors, and IDOS is a 
Universal Measurement Module (UMM). If you attach a 
UMM to the communications port (A1 - item [9]), the 

Select 

Task

 menu shows the applicable IDOS options.

Table 2: 

Menu options - Select Task

Table 3 shows all the one and two function operations that 
are available. If you attach a UMM, you can only use the 
options that include IDOS.

Table 3: 

Permitted 1 and 2 function operations

To start - Set up the settings

When the task is set up (Table 2/3), use the 

Settings

 menu 

to adjust the measurement operation.

If there is additional data for a menu option, select 

Settings

(

■ ■

) to see the values that are set up. If 

necessary, adjust the values. Refer to “Edit functions”

Table 4: 

(Part of table)

 

Menu options - Settings

1

Menu:

Select Task

2

3

Display:

Task 1xxx g


(Table 2/3)

Sk2 = Settings

Options

(If applicable)

Description

(* Optional item)

 

P...

An input measurement task (P1, P2*). The task 
includes the pressure range for the sensor.

 

P...

An input measurement task to measure the 
pressure difference (

) between: P1 and P2*, or 

P1/P2* and a UPM*. 

P = High range IDOS - Low range IDOS

mA

DPI 802/802P only. A mA measurement task. 

mA(24V)

DPI 802/802P only. A mA measurement task + the 
loop power supply is on. 
DPI 802/802P only. A switch test. 

 

IDOS

UMM only. An IDOS measurement task. 

 

Pressure options only. A leak test. 

To set up the way the instrument works.

Additional data: Refer to: Set Up 

(Table 1).

Function

P1

P2

P... 

(Table 2)

IDOS

(1)

(1)

(1)

(1)

mA

(1) (2)

(2)

(2)

(2)

mA(24V)

(1) (2)

(2)

(2)

(2)

x

(2)

(2)

(2)

(2)

x

(2)

(2)

x

(2)

IDOS

(1) (2)

(2)

x

x

P2

(1) (2)

x

x

(2)

= DPI 802/802P only

Display: Task 

P1 + mA

1

Settings selection 

(If applicable)

2

3

 

Sk2 = Settings

Menu:

Settings

4

5

6

Settings

x:y 


 

(Table 4)

[

]/[  ]

Sk1 = Edit

Options

(If applicable)

Description

... Units To select one of the fixed units of measurement 

(psi, mbar ... ).
Gage sensors or sensors with differential 
operation (P1, P2, IDOS). A zero correction that 
makes the instrument read zero at local pressure.
To include maximum, minimum and average 
values for the measurement task. 
To select and set up a tare value for the 
measurement task (a specified value or the 
reading on the display). 
The instrument subtracts a positive tare value, and 
adds a negative tare value.

Additional data: Select Settings 

(

 

)

To select and set up a scale of values: One local 
scale for each measurement task (Maximum: 5). 

Additional data (Example 1/2): Select Settings 

(

 

)

Содержание Druck DPI 800
















Отзывы: