GE Druck DPI 800 Скачать руководство пользователя

Страница: 14 / 15

- [EN] English

K335 Issue 3

Table 10:

DPI 800 series pressure connections

Table 11:

Maximum pressure (+ port)

Table 12:

Maximum pressure (Reference port)

Specification - Electrical connectors (A2)

Ranges

Pressure connections

(One IDOS range)

Pressure connections

(Two IDOS ranges)

g/d:

≤

30 psi g (2 bar g)

Standard or Premier

1/8 NPT female (+ port) + 1/8 NPT female reference
port OR
G1/8 female (+ port) + G1/8 female reference port

Two 1/8 NPT female (+ port) + 10-32 UNF reference
port OR
Two G1/8 female (+ port) + M5 reference port

g/d:

30 psi g (2 bar g)

Standard only

1/8 NPT female (+ port) OR
G1/8 female (+ port)

Two 1/8 NPT female (+ port) OR
Two G1/8 female (+ port)

g/d:

30 psi g (2 bar g)

Premier only

1/8 NPT female (+ port) + 10-32 UNF reference port OR
G1/8 female (+ port) + M5 reference port

Two 1/8 NPT female (+ port) + 10-32 UNF reference
port OR
Two G1/8 female (+ port) + M5 reference port

sg or a: all ranges

G1/8 female (+ port) OR
1/8 NPT female (+ port)

Two 1/8 NPT female (+ port) OR
Two G1/8 female (+ port)

Ranges: g/d, sg, a

MWP

Maximum transient /
intermittent pressure

≤

5 psi (350 mbar)

2 x FS

4 x FS

5 psi (350 mbar)

1.2 x FS

2 x FS

Ranges: g/d only

MWP

≤

5 psi (350 mbar)

2 x FS

10 to 15 psi
(700 mbar to 1 bar)

1.2 x FS

≥

30 psi (2 bar)

Range (Measure)

0 to ±55 mA

Accuracy

0.02% of r 3 counts

Temperature coefficient
14 … 50°F, 86 … 122°F
(-10 … 10°C, 30 … 50°C)

0.0011% FS / °F
(0.002% FS / °C)

Switch detection

Open and closed. 2 mA current.

Loop power output

24 V ± 10%

HART

resistor

250

Ω

(menu selection)

Connectors (A2)

Three 0.16 in (4 mm) sockets

Содержание Druck DPI 800
















Результаты поиска

Содержание Druck DPI 800

Отзывы:

Похожие инструкции для Druck DPI 800

Бренды по названию

Популярные бренды

GE Druck DPI 800, Руководство пользователя

Результаты поиска

Содержание Druck DPI 800

Отзывы:

Похожие инструкции для Druck DPI 800

Бренды по названию

Популярные бренды