manualshive.com logo in svg

GE Corometrics 250cx Series, Руководство по обслуживанию

Описание продукта GE Corometrics 250cx Series: Операторский мануал для вашего удобства. Скачайте бесплатно руководство по эксплуатации с серии 250cx на manualshive.com. Получите всю необходимую информацию для эффективного использования продукта.

Поделиться
Скачать
background image

Revision C

250cx Series Maternal/Fetal Monitor

i

2036947-001

Contents

1

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1-1

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1-1

Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1-3

Responsibility of the Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Responsibility of the User   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
References to Persons, Places, and Institutions  . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Hazard Definitions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Product Specific Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Electromagnetic Interference  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1-9

Equipment Symbols   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1-10

Service Requirements  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1-11

Equipment ID  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Intended Audience  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Intended Use  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Related Manuals   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

2

Equipment Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2-1

Equipment Description  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2-3

Front Panel Description   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2-4

Front Panel Displays  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2-7

Display Example   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Setup Screens  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Softkeys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-8

Mode Title Softkeys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Waveform Softkeys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Dedicated Softkey Area  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Rear Panel Description  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2-12

Optional Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2-14

Software Upgrades   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Adding Spectra Alerts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Adding Fetal Movement Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Содержание Corometrics 250cx Series





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Corometrics 250cx Series

Landoll 2210 Operator'S Manual preview
2210
Бренд: Landoll Страницы: 52
JBSYSTEMS Light Premium Operation Manual preview
Premium
Бренд: JBSYSTEMS Light Страницы: 14
Magicfx FX-ARM CONTROLLER User And Installation Manual preview
FX-ARM CONTROLLER
Бренд: Magicfx Страницы: 16
Panasonic LP-GS Series Serial Communication Command Manual preview
LP-GS Series
Бренд: Panasonic Страницы: 180
JB Systems Sirius Operation Manual preview
Sirius
Бренд: JB Systems Страницы: 7
3B SCIENTIFIC PHYSICS 1023095 Instruction Sheet preview
1023095
Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36
3A HEALTH CARE HAPPYNEB III Instruction Manual preview
HAPPYNEB III
Бренд: 3A HEALTH CARE Страницы: 16
360 Systems Short/cut 2000 Audio Editor Specification preview
Short/cut 2000 Audio Editor
Бренд: 360 Systems Страницы: 4
AAON RQ SERIES Manual preview
RQ SERIES
Бренд: AAON Страницы: 36
NANLUX TK-200 Manual preview
TK-200
Бренд: NANLUX Страницы: 39
jablotron JA-65ST Quick Start Manual preview
JA-65ST
Бренд: jablotron Страницы: 2
Parkside PFMR 1400 A1 Original Operating Instructions preview
PFMR 1400 A1
Бренд: Parkside Страницы: 58
PASCO ME-9430 Instruction Manual And Experiment Manual preview
ME-9430
Бренд: PASCO Страницы: 30
Raytec VARIO2 series Full Installation And Setup Manual preview
VARIO2 series
Бренд: Raytec Страницы: 60
Yamaha TG300 Sound List & Midi Data preview
TG300
Бренд: Yamaha Страницы: 39
Yamaha MU100 Supplementary Manual preview
MU100
Бренд: Yamaha Страницы: 110
Y.I.C. TECHNOLOGIES EMScannerR Setup Manual preview
EMScannerR
Бренд: Y.I.C. TECHNOLOGIES Страницы: 6
B medical systems MRB 3000 SDD Instructions For Use Manual preview
MRB 3000 SDD
Бренд: B medical systems Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды