manualshive.com logo in svg

GE Corometrics 250cx Series, Руководство по обслуживанию

Описание продукта GE Corometrics 250cx Series: Операторский мануал для вашего удобства. Скачайте бесплатно руководство по эксплуатации с серии 250cx на manualshive.com. Получите всю необходимую информацию для эффективного использования продукта.

Поделиться
Скачать
background image

T-2

Corometrics 250cx Series Monitor

Revision C

 

2036947-001

26-Sept-2007

Corometrics

 and 

Marquette

 are registered trademarks of GE Medical Systems 

Information Technologies

. 

GE

 is a 

registered trademark of General Electric Company. All other product and brand names are trademarks or registered 
trademarks of their respective companies. ©2005, 2006, 2007 GE Medical Systems 

Information Technologies

. All rights 

reserved. No part of this manual may be reproduced without the permission of GE Medical Systems 

Information 

Technologies

. 

GUARANTEE

All equipment sold by GE Medical Systems 

Information Technologies

, is fully guaranteed as to 

materials and workmanship for a period of 1 year. GE Medical Systems 

Information 

Technologies

 reserves the right to perform guarantee service operations in its own factory, at 

an authorized repair station, or in the customer’s installation.

Our obligation under this guarantee is limited to repairing, or, at our option, replacing any 
defective parts of our equipment, except fuses or batteries, without charge, if such defects 
occur in normal service.

Claims for damage in shipment should be filed promptly with the transportation company. All 
correspondence covering the instrument should specify the model and serial numbers.

GE MEDICAL SYSTEMS 

Information Technologies

A GE Healthcare Company

NOTE: 

In addition to software version 4.50, the information in this manual also applies to previous software 

revisions of Corometrics 250cx Series Monitor. There are no user-apparent differences among these software 
versions. Due to continuing product innovation, specifications in this manual are subject to change without notice.

NOTE: 

For technical documentation purposes, the abbreviation GE is used for the legal entity name, GE Medical 

Systems 

Information Technologies

GE Medical Systems 

Information Technologies

 will make available on request such circuit diagrams, component 

diagrams, component parts lists, descriptions, calibration instructions, or other information which will assist the users 
or appropriately qualified technical personnel to repair those parts of the equipment which are classified by GE 
Medical Systems 

Information Technologies

 as repairable. Refer to the 

250cx Series Service Manual

 for further 

information.

CAUTION:

 In the United States of America, Federal Law restricts this device to sale 

by or on the order of a physician.

Ohmeda Oximetry and other trademarks (

®

, PI

r

™, TruSat™, TruSignal™,

®

, SuperSTAT™) are the 

property of GE Medical Systems 

Information Technologies

, a division of General Electric Corporation. All other product 

and company names are the property of their respective owners.

MASIMO SET

®

 is a trademark of Masimo Corporation. Possession or purchase of this device does not convey any 

express or implied license to use the device with replacement parts which would, alone, or in combination with this 
device, fall within the scope of one or more of the patents relating to the device.

NELLCOR

®

, OxiMax

®

, C-LOCK

®

 and 

SatSeconds

™ are trademarks of Nellcor Puritan Bennett.

 

TAT-5000™, Exergen

®

, and TemporalScanner™ are trademarks of Exergen Corporation. 

Содержание Corometrics 250cx Series





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Corometrics 250cx Series

Makerfire N10 Instructions Manual preview
N10
Бренд: Makerfire Страницы: 10
Laica SB2200 Instructions And Guarantee preview
SB2200
Бренд: Laica Страницы: 4
MacDon 912 Operator'S Manual preview
912
Бренд: MacDon Страницы: 84
MacDon 625 Operator'S Manual preview
625
Бренд: MacDon Страницы: 89
Patton electronics 2012 Installation And Operation Manual preview
2012
Бренд: Patton electronics Страницы: 18
Makita KP312 Operating Manual preview
KP312
Бренд: Makita Страницы: 8
VECTECH 190 Instruction Manual preview
190
Бренд: VECTECH Страницы: 5
lancer 9000 series Installation Manual preview
9000 series
Бренд: lancer Страницы: 12
VeEX FX30 Quick Manual preview
FX30
Бренд: VeEX Страницы: 2
JB-Lighting P8 Operating Instructions Manual preview
P8
Бренд: JB-Lighting Страницы: 48
Baker D30R User Manual preview
D30R
Бренд: Baker Страницы: 82
Daga AB Directions For Use Manual preview
AB
Бренд: Daga Страницы: 24
DAF DAVIE XDc II Quick Start Manual preview
DAVIE XDc II
Бренд: DAF Страницы: 68
Datalogic Heron HD3430 Quick Reference Manual preview
Heron HD3430
Бренд: Datalogic Страницы: 48
PageFlip Firefly Quick Start Manual preview
Firefly
Бренд: PageFlip Страницы: 32
ECE Zen-O lite Quick Start Manual preview
Zen-O lite
Бренд: ECE Страницы: 2
Ecco 6221000 Series Installation And Operation Instructions preview
6221000 Series
Бренд: Ecco Страницы: 5
Bakare Evolution Series Instructions Manual preview
Evolution Series
Бренд: Bakare Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды