![background image](http://html.mh-extra.com/html/ge/aph10-series/aph10-series_owners-manual-and-installation-instructions_2198709004.webp)
4
Consumer Support
Tr
oubleshooting T
ips
Operating Instructions
Safety Instructions
Tr
oubleshooting T
ips
Care and Cleaning
Safety Instructions
Operating Instructions
About the controls on the air conditioner.
Controls
ON/OFF Pad
Turns the air conditioner on and off.
Display
Shows the room temperature. Also shows the
set temperature while setting the temperature
in
COOL
mode or the set time while setting
TIMER ON
or
TIMER OFF
.
NOTE:
The display will change to show the
room temperature after settings have been
made. To recall the set cooling temperature,
press the
or
pad. To recall the timer
setting, press the
TIMER ON
pad or the
TIMER
OFF
pad for the timer that is set.
MODE
Use to set the air conditioner to
COOL, DRY
or
FAN
mode.
Increase /Decrease Pads
Use to set temperature when in
COOL
mode
or to set a time with the timer feature.
FAN Pad
Use to set the fan speed to
LOW, MEDIUM
or
HIGH.
CIRCULAIRE
Turn on to provide continuous side-to-side
air circulation.
For fixed side-to-side air direction, turn on
until the desired air direction is obtained,
then turn it off.
TIMER Pad
ON—
The air conditioner can be set to
automatically come on in 1/2 (0.5) to 24 hours
at its previous setting. The unit must be on
while setting
TIMER ON
.
1.
Press the
POWER (ON/OFF)
pad.
2.
Press the
TIMER ON
pad. The
TIMER ON
light will blink.
3.
Press the
or
pad to set the desired
time for the unit to start. (Each time you
touch the
or
pads, the set time will
advance by 30 minutes between 0 and 10 hours
and by one hour between 10 and 24 hours.)
4.
Press the
TIMER ON
pad again to start the timer.
5.
Press the
POWER (ON/OFF)
pad to turn the
unit off.
TIMER Pad (cont.)
OFF—
When the air conditioner is on, it can
be set to automatically turn off in 1/2 (0.5)
to 24 hours.
1.
Press the
TIMER OFF
pad. The
TIMER OFF
light will blink.
2.
Press the
or
pad to set the desired
time for the unit to stop. (Each time you
touch the
or
pads, the set time will
advance by 30 minutes between 0 and 10
hours and by one hour between 10 and 24
hours.)
3.
Press the
TIMER OFF
pad again to start
the timer.
After settings have been made, the display will
change back to show the room temperature.
NOTE:
Both timers may be set, in combination,
to turn the unit on and off as desired.
To cancel the timer,
press and hold the
TIMER
ON
or
TIMER OFF
pad (depending on the
timer(s) set) until its indicator light goes off.
Remote Control Signal Receiver
Water Full Indicator Light
When the Water Full Indicator Light begins
blinking, the unit has reached maximum
water collection level.
If water level does not lower in 40 minutes,
the unit will power off and it must be
manually drained.
1.
Unplug the power cord and roll the unit
to a drain or outside.
2.
Pull out the drain cap from the back
bottom edge and allow water to drain
from the unit.
3.
Replace the drain cap and put the unit
back into operation.
NOTE:
The unit is designed to automatically
evaporate water collected in normal settings.
However, in very humid settings, the unit may
occasionally need to be drained.
Air Conditioner Control
Remote Control
Cool
Mode
On
Dry
Mode
On
Fan
Mode
On
Low
Fan
On
Medium
Fan
On
High
Fan
On
Timer On
Timer Off
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.