GE AIR F24 Скачать руководство пользователя страница 19

Страница: 19 / 48

－

preset

7.1.2.3 Heating Mode

When T

amb.

≤

preset

-1 , the unit will run under heating mo

℃

de, in which case the 4-way valve, compressor and

outdoor fan will be started, while the indoor fan will run at preset speed under preset cold air prevention condition.

If T

amb.

≥

preset

+1 , the compressor and outdoor

℃

fan will be stopped, the 4-way valve is still energized and the indoor

fan will run at low speed for 10 seconds before it is stopped.

When T

preset

-1 <T

℃

amb.

< T

preset

+1 , the unit will maintain its original operating status.

℃

Under heating mode, the temperature can be set within a range from 16 to 30 . The initial value is 25 .

℃

If the unit is switched off under heating mode or switched to another mode, the 4-way valve will be de-energized 2

minutes after the compressor is stopped.

Start cooling

Ambient temperature T

amb

Maintain original operating status

6 min. 3 min. 6 min. Stop cooling

Compressor

Outdoor fan

Indoor fan

≤

5 minutes

Preset speed

≤

5 minutes

Preset speed

Louver valve

Run Stop

7.1.2.3.1 Cold Air Prevention Condition

The compressor will start at heat mode, indoor fan will not operate. After 5Min or if the outlet temperature is high, the

indoor fan will run at preset speed. The indoor fan will no longer be stopped once it is started. Once running at preset

speed, it will be impossible to change the speed of the indoor fan.

7.1.2.3.2 Defrosting Conditions

When the condenser is detected to have frost, the system will enter into defrosting mode, in which case the 4-way

valve, indoor fan and outdoor fan will be stopped.

When it is detected that the frost in condenser is completely eliminated, the 4-way valve and outdoor fan will be

started simultaneously, while the indoor fan will start to run under preset cold air prevention condition.

≤

10 min.

Compressor

Outdoor fan

Indoor fan

≤

3min.

Preset speed

Run Stop

7.1.2.4 Fan Mode

Indoor fan will run at preset speed

Auto Speed

Low Speed

Medium Speed High Speed

The temperature can be set within a range from 16 to 30 . The initial value is 25 .

℃

7.1.2.5 Auto Mode

Under this mode, the system will automatically select its run mode (cooling, dehumidifying, heating or fan) depending on

ambient temperature.

Once a mode is started, the unit will run at least 30 seconds before it can run the status of auto mode depending on

ambient temperature.

7.1.3 AUTO ON/OFF and Sleep Function

7.1.3.1 Sleep

If the controller is under cooling or dehumidifying mode, the preset temperature will be increased by 1 one hour

℃

after running under sleep mode and will be increased by another 1 after two hours. The temperature will increased

℃

by 2 within two hours. After that, the unit will run at this temperature.

℃

Содержание AIR F24

















































Результаты поиска

Содержание AIR F24

Отзывы:

Похожие инструкции для AIR F24

Бренды по названию

Популярные бренды

GE AIR F24, Руководство по обслуживанию

Результаты поиска

Содержание AIR F24

Отзывы:

Похожие инструкции для AIR F24

Бренды по названию

Популярные бренды