background image

17

a.

Gate Drive Systems Australia warrants that the goods manufactured by it shall be free from defect in

manufacture for a period of 12 months from the date of invoice.  Should any fault occur within that period as a

result of faulty workmanship or materials, Gate Drive Systems Australia at its discretion, replace the product at

no charge to the Customer except for removal, installation & freight.  The appropriate Serial Number must be

quoted for all warranty claims.

b.

For the goods not manufactured by Gate Drive Systems Australia, we shall pass on the manufacturer`s warranty

to the Customer from the date of invoice.  It is the manufacturer`s discretion to repair or replace goods deemed

to be defective as a result of faulty workmanship or materials.

c.

All goods must be returned to Gate Drive Systems Australia or its representative for inspection or testing to

assess if a claim is justified.  It is the responsibility and at the cost of the Customer, to remove & return the

goods for inspection and freight costs are the responsibility of the Customer.

d.

The warranty is negated and will not apply in the following circumstances:-

i.

If no proof of date of purchase can be produced.

ii.

If the product has been used in a manner beyond its design parameters.

iii.

If the product is tampered with or repaired by personnel not authorised to do so.

iv.

In respect of loss or damage caused by rough treatment.

v.

If the product is not used and maintained in accordance with instructions or recommendations listed in

this Installation and Maintenance Manual.

vi.

In respect of loss or damage caused by an Act of God or any other cause not within the manufacturers

control.

e.

Goods returned under warranty for repair or testing will incur a charge to be fixed by the manufacturer if no

fault is found.

f.

The Customer shall bear freight charges for removing & returning the goods for inspection and for the delivery

& installation of any replacement or repaired product from a justified warranty claim.

g.

Save for the express conditions and warranties herein contained all other conditions or warranties (whether as

the quality, fitness for purpose or any other matter) expressed or implied by statute, common law, equity, trade

custom, usage or otherwise are hereby expressly excluded provided that nothing in these terms and conditions

shall exclude or limit any breach or condition implied by law, the exclusion or limitation of which is not

permitted by law.

9

.

W

ARRANTY

Содержание 450P I


















Отзывы: