GBS SureBind System Two, Инструкция по эксплуатации

Страница: 5 / 14

5
G
Punching
1
Place the paper fully in the punch, slide the paper to the left
against the Punch Edge Guide and press the ‘Punch’ button.
2
To prevent jamming only 22 sheets of 80g/m
2
(20lbs bond)
paper should be punched at one time (fewer sheets if the
paper is heavier). Punch one 22 sheet segment of your
document and stack the punched sections on the binding
surface. Do not punch more than 4 composition covers or 3
transparent covers at one time.
3
If you try to punch too much paper the Jam-Stopper™
feature will sense the high paper load and will retract the
punch pins and you will hear a beeping sound. Simply
separate the paper and lift and punch fewer pages at a time.
4
Remember to lay each punched segment of your documents
on the Binding Surface as you work. Preassembling your
document on another surface can cause binding problems
due to improper location of the receiving strip (not on the
Locating Pin).
Service
• Do not attempt to service or repair the equipment yourself.
Unplug the unit from the electrical outlet and contact an
authorized service representative under the following
conditions:
- When the power supply cord or plug is damaged or frayed
- If liquid has been spilled into the equipment
- If the binding system has been exposed to rain or water
- If the unit has been subjected to excessive shock through
being dropped or rough handling
- If the unit does not operate normally when following these
Operating Instructions
• Adjust only those controls that are specified in these
Operating Instructions.
Care Instructions
• Wipe exterior only with a damp cloth. Do not use any
detergents or solvents.
• Empty the Debris Tray frequently. Failure to empty the
tray may result in debris lodging in the equipment and
causing damage to the equipment.
Features Guide
A. Debris Tray
The Debris Tray is located on the front side near the bottom
of the machine. It collects excess paper and pin segments.
The Tray should be emptied frequently.
B. Punching Surface
The flat area is where your document is placed for punching
holes.
C. Punch Edge Guide
An adjustable Guide positions the paper for punching.
Using the scale the Guide can be adjusted for 210mm,
297mm (8½″, 11″, 13″ or 14″) bind edge lengths.
D. Binding Surface
The Binding Surface is a flat area where the document is
placed for binding after it has been punched.
E. Bind Edge Guide
An adjustable Guide properly aligns the paper for binding.
F. Locating Pin
The Locating Pin can be found near the lower left hand
side of the Backstop where the word ‘PIN’ and an arrow are
printed.
G. Backstop
The Backstop serves to position the paper along with the
Bind Edge Guide so that the holes are easily aligned for
easy insertion of the strip with pins. The Backstop also has a
scale that measures document thickness to help select the
proper length of the strip with pins or correct hard cover size.
H. Pressure Bar
The Pressure Bar exerts pressure on the document and
contains the trigger which starts the bind cycle.
I. Strip Recess
The Strip Recess supports the receiving strip (binding strip
with holes).
J. Bind Button
Press the Bind Button to activate the bind process after
placing the Pressure Bar on the document.
K. Punch Button
Press the Punch Button after you have aligned the paper
fully in the Punch Edge Guide. The punch will operate every
time the Punch Button is pressed.
L. Ready Indicators
When the equipment is turned on the indicator will light.
During binding the indicator will flash, but will return to a
steady light when the bind cycle is complete.
M. Tray Full
The Tray Full indicator will light up when the Debris Tray is
full and must be emptied.
N. On/Off Switch
Power must be turned ‘ON’ for both punching paper and
binding documents. Remember to turn off the equipment at
the end of the day.
Set-Up
1
Adjust the Punch Edge Guide to the correct paper length.
2
Check the Bind Edge Guide alignment by inserting a
receiving strip in the Strip Recess area. Lay a sheet of
correctly aligned punched paper on the strip, matching up
the holes and the strip so that the strip is not showing at the
top or bottom of the paper. Adjust the Guide if necessary by
loosening the thumb screw on top of the Guide and sliding
the Guide to the edge of the paper.
1
Installation
1
Inspect your equipment for shipping damage. Bring damage
immediately to the attention of the delivery carrier.
2
Place the equipment on a sturdy, flat surface of the
appropriate height for the comfortable operation.
CAUTION: THE SOCKET OUTLET SHOULD BE
LOCATED NEAR THE EQUIPMENT AND SHOULD
BE EASILY ACCESSIBLE.
3
Plug the power cord into the receptacle on the rear right side
of the unit and into a proper power source.
4
Place the machine at least 2″ (51mm) from any wall or
obstruction to protect the power receptacle and power cord.
m