background image

Page 6-13

SPIRE III Series

 – Installation and Operating Instructions

F

Ilm

 a

lIGnment

The top and bottom supply rolls must be aligned 
as closely as possible. Misalignment can cause 
adhesives to stick to the rollers. The 3 inch Extruded 
AUTOGRIP Shafts have rulers incorporated to assist 
centering the film on the shafts.

Figure 56.  Measuring rules on Shafts to align the rolls.

To align the supply rolls:

1.  With the film roll on the shaft, note the 

measurement on each end of the shaft.

2.  Shift the roll side to side to ensure that the two 

measurements are equal.

F

Ilm

 t

ensIon

Proper film tension, known as brake tension, is the 
minimum amount required to eliminate wrinkles in 
the finished item. As the film roll becomes smaller, 
tension increases, thus the adjustment needs 
to be loosened. Film tension should be checked 
occasionally to ensure that the adjustment is correct.

The film should be taut with no gaps between the 
film and Main Rollers. A properly adjusted roll of 
film should not require excessive force to turn by 
hand. Film tension should be enough to introduce a 
minor amount of drag as the film unrolls. Insufficient 
tension causes wrinkles, while too much tension 
causes stretching (necking). Uneven tension between 
the top and bottom rolls create curl. Too much upper 
tension creates upward curl. Too much lower tension 
bottom creates downward curl. 

Refer to the “” section for information about each of 
the Adjustment knobs.

AlWAyS RElEASE All TENSION BRAkES, 
BOTH UPPER UNWIND AND REWIND, BEFORE 
lOADING THE FIlM. ONCE lOADED, START By 
ADDING TENSION TO THE REWIND FIRST.

t

estInG

 

tHe

 W

eB

After webbing the machine, it is important that the 
films run straight and evenly. 

To test the web:

1.  Set the Roller Pressure Crank to an appropriate 

gap.

2.  Press 

RUN

 on the Control Panel or press the 

Footswitch 

and run approximately 6 in. (10 cm) 

of laminate.

3.  Press 

STOP

 or release the 

Footswitch

.

4.  Visually inspect the top and bottom films where 

they enter the point between the two Main 
Rollers.  
The films should be tight against the rollers 
at both ends. If they are not, use the tension 
adjustment knobs to tighten the loose supply film 
brake and run another test.

5.  Ensure that the release liner take-up keeps the 

liner loose against the idler bar.  
Use the upper film supply tension knob to 
properly tension the release liner.

6.  Run test materials before laminating good 

materials.

l

amInatIon

 G

uIde

 

This manual provides general guidelines and is only 
a general reference guide. Different settings may be 
suitable as the lamination time and materials change. 
Test materials before running good materials through 
the machine.

•  Do not attempt to laminate abrasive or metal 

objects such as staples, paper clips and 
glitter, as they may damage the rollers.

•  Do not force items into the point between the 

two Main Rollers. An item that is not easily 
drawn into the laminator by the rollers is 
probably too thick to laminate.

•  Wrinkles may result if an attempt is made to 

reposition an item once it has been grasped 
by the rollers.

•  Do not stop the laminator before an item has 

completely exited the Main Rollers. Even a 
momentary stop may cause a mark on the 
laminated item.

•  Good, consistent lamination is a result of 

combining proper tension and roller pressure.

•  Do not combine thick and thin items at the 

same time, as this will result in a poor edge 
seal around the thinner material.

Содержание Spire III 44T


















































Отзывы: