GBC Magnapunch 2.0, Руководство по установке и эксплуатации

Страница: 21 / 120

Page 6-1
Magnapunch 2.0
– Installation and Operating Instructions
6. o
peRation
The Magnapunch 2.0 uses a variety of easily
interchangeable Die Sets for different binding styles.
By selecting the appropriate Die Set, you can use
your Magnapunch 2.0 to punch documents in any of
the binding styles indicated in the following table.
Punch Styles Table 1.
Binding Style Punch Pattern
Minimum Margin
to First Binding
Hole
CombBind®
Cerlox (Plastic Comb, Plastic Binding)
0.282 in. (7.2 mm)
Color Coil®
4:1 GBC (4 holes per inch 0.2475” center-to-center hole spacing)
0.092 in. (2.6 mm)
Color Coil
4:1 Industry Standard (4 holes per inch, 0.2500” center-to-center
hole spacing) 0.040 in. (1.0 mm)
Color Coil 5:1 (5 holes per inch)
1 0.030 in.
(0.8 mm)
WireBind®
2:1 (2 holes per inch) Both square and round hole patterns
available. 0.375 in. (9.5 mm)
WireBind
3:1 (3 holes per inch) Both square and round hole patterns
available. 0.261 in. (6.6 mm)
VeloBind 1 hole per inch 0.500 in. (12.7 mm)
SureBind®
Approximately 1 hole per inch
0.531 in. (13.5 mm)
3, 5, or 7 Hole Binding 11 in. 3 holes across bound edge of document, 11 inch paper
2 or 4 Hole Binding A4 4 holes across bound edge of document, A4 paper
Note: Each punching style listed in the table requires
a separate Die Set for the Magnapunch 2.0. Custom
Die Sets for special punching patterns (not listed
above) can also be made to your specifications. For
more information on custom Die Sets, contact your
local GBC sales representative.
IMPORTANT: A decal on the handle of each
interchangeable Die Set indicates the punching
pattern for that Die Set. When reading the Operating
Instructions, please note the special instructions for
the correct punching pattern Die Set that you have
installed in your Magnapunch 2.0.
WARNING:
Do not attempt to service or repair
the Magnapunch 2.0. Failure to observe this warning
could result severe personal injury or death.
Disconnect the plug from the receptacle and contact
your dealer or distributor, or GBC Technical Service
at one of the numbers below when one or more of
the following has occurred.
The power supply cord or attachment plug is •
damaged.
Liquid has been spilled into the Magnapunch
•
2.0.
The Magnapunch 2.0 is malfunctioning.
•
The Magnapunch 2.0 does not operate as •
described in these instructions.
US - 800-723-4000
Canada - 800-463-2545
Mexico - (5525) 1500-5741
CAUTION:
The receptacle must be located near •
the Magnapunch 2.0 and must be easily
accessible.
Disconnect the attachment plug from the
•
receptacle to which it is connected and keep
the power supply cord in your possession
while moving the Magnapunch 2.0.
Do not use the Magnapunch 2.0 for other than
•
its intended purposes.
Do not defeat or remove electrical and
•
mechanical safety equipment such as shields
and guards.
Do not insert objects unsuitable for punching •
or expose the equipment to liquids.
Use only GBC Magnapunch 2.0
•
interchangeable Die Sets with the
Magnapunch 2.0.
Failure to observe these warnings could result in
severe bodily damage or death.