gazex MDP-4 Скачать руководство пользователя страница 23

NOTE! IMPORTANT!!

 

7.3. All: 
- results of each system inspection acc. to section 6.3. of this instruction, 
- situation, when the A2 alarm state was generated along with actions taken by the personnel, 
- stoppage of unit’s supply for more than 3 months,  
- any observed unusual symptoms in system operation 

 

NEED TO BE included in the attached Periodical Control Protocol or otherwise you can lose warranty for system 
elements and the Manufacturer will be released from any responsibility for operation of the System.  

 

7.4.  After 5 years from the date of production absolutely change internal batteries and  

(for MDP-4(8,16).(Z,ZA,ZB)) the internal rechargeable battery for new ones. Paid service, provided by the 
Manufacturer.  

 

7.5. 

NOTE:

 any attempt of interference in the internal circuits of the MDP unit breaches the warranty 

conditions and causes blocking of the unit’s operation (the message on the display: “Blocked 

control unit. To unlock call to…“). Removal of the blocking can be performed 

only by GAZEX service (extra paid). 

 

7.6.  According to 2002/96/EC Directive on waste electrical and electronic equipment (WEEE), 

the waste unit (classified as group 9.5 equipment in accordance with the above Act) cannot 
be stored with other wastes. Therefore it was marked with a special symbol: 

 
 
 

8. STORAGE 

 

 

In order to care for the internal battery (and a possible rechargeable battery - in version MDP-4(8,16). 

(B,Z,ZA,ZB)), it is recommended to store the unit in dry locations with temperature within the range of 

+5

°

C to +35

°

C. A short-term (<2h/8h) storage in ambient temperature from 

-10

°

C do 45

°

C is permitted.

 

When storing the MDP-4(8,16).(B,Z,ZA,ZB) for a longer time, the internal battery should be 

recharged every 6 months. Recharging is performed by adding the 230V~ or 12V= voltage depending on MDP 
version (without detectors connected) for the period of at least 24 hours. After that time switch the power off. 

NOTE!!!

 To disable power supply in the unit in MDP-4(8,16).(B,ZB) version equipped with internal battery support, 

disconnect the external power supply with main switch, then press "OK" button located on the front panel and hold 
it down until you disable the MDP (for about 10 seconds). 

Internal battery service life is calculated at approximately 3 to 5 years (depending on operating conditions), 

and the internal memory backup battery - for 5 years from the date of manufacture. After 5 years from the date of 
manufacture replace the battery and the rechargeable battery with a new - exchange can be conducted only by the 
Manufacturer. 

 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

MDP-4(8,16)… Instruction Manual  

edition 6PU63en   

©gazex’2011 v1101

  

Page 23

 

/ 24

 

Содержание MDP-4

























Отзывы: