Gazelle GW7030, Руководство пользователя, Страница: 5 / 12

5
EN
To avoid
kickback,do
suppoet board or
panel near the cut.
Do not support
board or panel
away from the cut.
e) Do not use dull, deformed, cracked or damaged
blade.
f) Blade depth and bevel adjusting locking levers
must be tight and secure before making cut.
g) Use extra caution when making a “Plunge Cut”
into existing walls or other blind areas.
Safety instructions for circular saws with swing
guard
a) Check lower guard for proper closing before each
use. Do not operate saw if lower guard does not
move freely and close instantly. Never clamp or tie
the lower guard into the open position.
b) Check the operation and condition of the lower
guard spring. If the guard and the spring are not
operating properly, they must be serviced before
use.
c) Lower guard should be retracted manually only for
special cuts such as “Plunge Cuts” and “Compound
Cuts”. Raise lower guard by Retracting Lever. As
soon as blade enters the material, lower guard must
be released.
d) Always observe that the lower guard is covering the
blade before placing saw down on bench or floor.
Additional safety instructions for various circular
saws with riving knife
a) Use the appropriate riving knife for the blade being
used.
b) Adjust the riving knife as described in this instruction
manual.
c) Always use the riving knife except when plunge
cutting.
d) For the riving knife to work, it must be engaged in
the workpiece.
e) Do not operate the saw if riving knife is bent.
Additional supplements when using a circular
saw
a) When using this tool, note that:
- The blades used shall be intact and shall not be
deformed, rolled, tooth-missing or cracked;
- Saw blades made of HSS shall not be used, and
tools shall not use any grinding wheel;
- Do not use blades that do not conform to the
characteristics specified in this manual;
- Do not apply lateral pressure on the blade disc
surface to stop the blade;
- Ensure that all the retracting mechanisms of the
protection system are acting correctly;
-Unplug the blade from the power supply before
replacing the blade, making adjustments or other
maintenance work.
b)The maximum diameter of the saw blade used in this
tool is 185mm
c)The rated no-load speed of this tool is 5300r/min.
d)Before using this tool, the blade teeth should be
opened, and the size of the opening teeth should be
guaranteed to be moderately kerf.
e)When using this tool, you should control the
moderate propulsion speed according to the
different hardness materials.
f)When using this tool, the processed wood shall not
have foreign objects such as nails, and in the event
of a hard knot of wood, the propulsion speed shall
be slowed down.
g)It is strictly forbidden to operate with the guard
removed.
h)To keep the blade clean and sharp, use sharp blades
to reduce failure and rebound to a minimum.
Danger: The hand must leave the work area when
operating. Do not touch the blade. Do not insert the
workpiece or touch the cut-off part when the blade is
turning.
i) Prevent rebounding safety devices
When the circular saw suddenly decelerates, a
rebound occurs, bouncing to the operator. When the
saw blade is clamped by the workpiece or suddenly
decelerates, the switch should be relaxed. Usually
should keep the blade sharp, the operator should be
shown in the figure method to support large pieces of
wood. Use a locating plate for longitudinal operation.
Do not force the use of tools, pay attention to work
management. When saw blade is still turning, do not
remove the circular saw from the workpiece. Never
put your hands or fingers behind a tool. Because if a
rebound occurs, the circular saw bounces easily back
into the hand and can cause serious injury.
When operating the saw, keep the cord away from the
cutting area and position it so that it will not be caught
on the workpiece during the cutting operation. Operate
with proper hand support, proper workpiece support,
and supply cord routing away from the work area.