background image

13

EN

12

BATTERY CHARGING

The battery should be charged according to 

the following steps:

Take the supplied charging cable and connect its 

magnetic connector to the counterpart on the back 

of the control box.

Plug the other end of the cable into the power 

adapter supplied or any standard powered USB-A 

port.

 The LED on the left side of the front panel (near the 

ON/OFF  button)  will  flash  red  indicating  the 

charging process. When the battery is fully charged, 

the red light will turn blue.

Wait until the charging is complete and disconnect 

the cable in the reverse order: the cable end from 

the  power  adapter  first  and  then  the  magnetic 

connector from the control box.

The Gauss MiL is powered by a built-in lithium-ion battery. The included USB charging cable 

with a magnetic connector is used to charge the battery.

Important! Strictly observe the 
procedure for connecting the 

charging cable indicated in this 
manual. Keep the magnetic cable 
connector away from metal particles 

to avoid short 
circuiting and 
breakdown of 
the power 
adapter or 
other device 

the charging 
cable is 
plugged into.

Important! To avoid battery 

damage, never charge a 

battery in an area with an ambient 

temperature of less than 5ºC. Always 

allow the control box to first warm up 

to room temperature for a few hours, in 

order to then charge the battery under 

optimum condition.

Battery maintenance

Lithium-ion battery may degrade if 

they aren’t in use for long periods of 

time. Fully charge the battery regularly, 

at least once every 2-3 months. 

However, be aware that the lithium-ion 

battery capacity decreases gradually 

with time, even under normal usage 

conditions. In view of this, the battery 

needs to be replaced every few years. 

Replacement batteries can be supplied 

and installed by an authorized service 

center.

The charging time for a completely 
discharged battery is estimated to be about 

5 hours if the charging adapter provides a power 
output of 5V and 1A. Less power from the power 
source may extend the charging time. If the 
detector is turned on while charging, the charge 
time will be longer.

To charge the Gauss MiL, the use of any quick charge AC power adapters is prohibited!

It may cause damage or destroy the battery. 

Use the power adapter supplied in the package.

1

2

3

4

Содержание MIL MD



















Отзывы: