background image

|  Care and Cautions  |  User Guide  |  

5

Overall Warnings

Damage  caused  by  misuse  may  void  the 

manufacturer’s warranty. Failure to comply with 

the following guidelines may result in injury or 

damage to the equipment. Additional warnings 

are found throughout the document.

GENERAL

This  simulator  is  constructed  of  material

that  approximates  skin  texture.  Therefore,

in  handling  the  model,  use  the  same  gentle

techniques  as  you  would  in  working  with  a

patient.

Do  not  wrap  this  or  any  other  Gaumard

product in newsprint.

Indelible marks made with ballpoint pens, ink

or marker cannot be removed.

Do  not  use  alcohol,  acetone,  Betadine®  or

any other antiseptic which contains iodine in this

or  any  Gaumard®  simulator.  These  products

could damage or stain the skin of the simulator.

Use of needles sizes 22 gauge and smaller

will extend the lifetime of the resealing skin and

tubing.

STORAGE

Improper storage may damage the simulator.

 

Keep it stored in the box and/or bag provided.

Store  the  simulator  in  a  cool,  dry  place.

 

extended storage should be between 32 - 85 

degrees F (0-29 Celsius). Other temperatures 

will cause the simulator to soften and slowly 

warp.

Do not stack or store heavy materials on top

 

of the box and/or bag.

It is acceptable to operate the simulator at an

 

ambient temperature of 95 degrees Fahrenheit

 

(35 Celsius) for a short period of time. 

CLEANING

Clean  the  skin  of  the  simulator  after  every

training  session.  The  skin  should  be  cleaned

with a cloth, dampened with diluted liquid dish

washing soap.

Always purge with clean distilled water and

then drain the vein reservoirs at the end of the

simulation  session.  Doing  so  will  retard  the

formation  of mold  and  prevent  clogging  of the

system.

We  recommend  flushing  veins  with  70:30

solution of clean water to isopropyl alcohol (IPA)

at least once per month to prolong the life of the

vasculature.
The  simulator  is  “splash-proof”  but  not  water-

proof.  Do not submerge or allow water to enter 

the interior of the simulator.

Содержание S402.100

























Отзывы: