background image

CERTIFICATE OF CONFORMITY

The symbol shown here means that the product is classed as Electrical or Electronic Equipment 
and should not be disposed with other household and commercial waste at the end of its 
working life. The Waste of Electrical and Electronic Equipment (WEEE Directive 2012/19/UE) 
has  been  put  in  place  to  recycle  products  using  best  available  recovery  and  recycling 
techniques to minimize the impact on the environment. Purchasers shall take any old electrical 
equipment to waste recycling public centers or points of sale.

PRODUCT DISPOSAL INSTRUCTIONS

GATE Menet, Wojtak Sp. J. hereby declares under our sole responsibility that the product
GATE NanoHARD is in conformity with the essential requirements of the following Directives:
EC DIRECTIVE 2011/65/EU
This product has been certified as RoHS Compliant.

WARNING:

WARNING:

WARNING:

WARNING: 

NOTE:

  Before  starting  installation  process,  please  ensure  that  your  AEG  is 

empty and there are no BBs inside.

 Always use a fuse between the battery and the mosfet.

 

Incorrectly  connecting  positive  and  negative  battery  terminals  will 

cause immediate damage to the unit and it can lead to fire.

To use the Battery Protection function (p.6), it must be enabled before 

(p.10).

Please check if you have downloaded the latest manual from the Technical Support 

section  of  our  website: 

www.gatee.eu

.  The  Product  Warranty  Form  is  also 

available there.

In  case  you  have  any  difficulties  while  installing  or  using  this  product,  we 

recommend to email us at 

[email protected]

.

USER GUIDE

03

WWW.GATEE.EU

Содержание 361813474

















Отзывы: