background image

                                                                                                Page 9    /    19 

The information given below is for guidance only and it cannot be assumed that it 
complies with national and local regulations. 

 
Consider  the  total  ventilation  requirements  for  simultaneous  operating  with  other  heating 
appliances.    For  this  appliance  only,  the  room  or  space  containing  this  appliance  needs  a 
permanent, unobstructed air opening of at least 825 mm

2

 to satisfy UK Building Regulations.   

Limited air for combustion may result in poor performance, smoking and other side effects of 
poor combustion. 
 
Every effort must be made to ensure that air vents installed for this appliance are kept clear of 
debris and in full working order at all times.    Preferably the grilles should be positioned as 
close to the appliance as practicable where air supply to the appliance will be unimpeded.   
 
There must not be an extractor fan fitted in the same room as the stove as this can cause the 
stove to emit fumes into the room 
 
The stove air input pipe diameter is ¢50 mm, venting pipe diameter is ¢80 mm. The total 
length of pipes is not longer than 3m. Indoor venting pipe joint should be sealed by silicone 
sealant  to  prevent  exhaust  leaking into  the room.  Venting  pipe and  termination should be 
waterproof and avoid being blocked. Or, the stove cannot work properly. 
 
When the installation is limited by space or the owner’s special requirements and the pipes’ 
length should be longer than 3m and need elbows, the diameters of the air input pipe and 
venting pipe must be increased properly for smooth convection. If not, it will influence the 
burning and the stove cannot work properly. The owner should connect with the local seller for 
the right installation.   
 
When the pellet stove is working normally, the temperature on venting pipe surface can reach 
200˚C, so combustible materials, clothes and furniture should be away from the venting pipe. 
To prevent burns, do not touch the heating surface! 
 
When installing the appliance, suitable access should be provided for cleaning the appliance, 
flue gas connector and chimney flue. 
 

Содержание HP24




















Отзывы: