GASTRON GTC-200A Скачать руководство пользователя

Страница: 25 / 28

GTC-200A

The completion message “End” is displayed for 2 seconds and return to

density display mode.

6-3-7. Test function display

Press “Test” key over 2 seconds in gas density display mode and go into
Test mode.

-. (During Test mode, automatically return to density display mode if there is

no key input for 30 minutes.)

-. Gas density display is flickering during Test mode and this mode is to

perform test without gas injection to sensor of gas detector. User can set
desired gas density with

“▲” or ▼” key and alarm is normally activated

with inputted density by user.

-. Press

”Func” key over 2 seconds and go into FND/LED/Bar LED Test

mode.

If pressing “RESET” key, returns to density display mode

-. This mode is for FND/LED/Bar LED Test and 4 digits number and 8888 are

displayed in turns on FND (0.5 second interval)
4 digits number represents PC address of common unit (SW1) and
channel number (SW2).

-.3 Color Bar Graphic LED shows green, orange and red color in turns and each

function LED is also flickering (0.5 second interval)

Press “Func” to go into next mode.

If pressing “RESET” key, returns to density display mode

-. This mode is to check channel unit normally communicated with Common

unit and normal channel unit number is displayed in turns (0.5 second
interval)

-. If some channel number is missing, this channel units can not

communicate with Common unit

Press “Func” key and returns to gas density test mode.

If pressing “RESET” key, returns to density display mode

6-3-8. Stand-by mode

Press “▼(Standby)” key over 2 seconds in gas density display status and
go into Stand-by mode.

Please make sure to press “▼(Standby)” key on channel unit during
stand-by mode, in order to return to density display mode.

-.During Stand-by mode, STD-BY LED is flickering and every function is

normal except trouble/alarm relay output of Common unit & Channel unit

-. Press

“▼(Standby)” key to return to gas density display mode.

Содержание GTC-200A





























Результаты поиска

Содержание GTC-200A

Отзывы:

Похожие инструкции для GTC-200A

Бренды по названию

Популярные бренды

GASTRON GTC-200A, Инструкция по эксплуатации

Результаты поиска

Содержание GTC-200A

Отзывы:

Похожие инструкции для GTC-200A

Бренды по названию

Популярные бренды