GAS GAS EX 250 2023 Скачать руководство пользователя страница 100

Страница: 100 / 144

15 COOLING SYSTEM

400243-10

–

Pour coolant in up to level

above the radiator fins.

Guideline

10 mm (0.39 in)

Coolant

1.2 l (1.3 qt.)

Coolant (

p. 131)

V01681-10

–

Push protection cap

upward over the coolant temperature sen-

sor.

V01682-10

–

Unplug connector

–

Remove coolant temperature sensor

with the O-ring and wait

until the coolant escapes without bubbles.

–

Mount and tighten coolant temperature sensor

with the O-ring.

Guideline

Screw, cylinder head

temperature sensor

M10x1.25

12 Nm (8.9 lbf ft)

–

Plug in connector

–

Position protection cap

400243-10

–

Pour coolant in up to level

above the radiator fins.

Guideline

10 mm (0.39 in)

Coolant (

p. 131)

E02035-11

–

Mount radiator cap

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling

them may result in unconsciousness and death.

–

Always make sure there is sufficient ventilation when

running the engine.

–

Use effective exhaust extraction when starting or run-

ning the engine in an enclosed space.

–

Allow the engine to warm up and cool down again.

Содержание EX 250 2023

















































































































































Результаты поиска

Содержание EX 250 2023

Отзывы:

Похожие инструкции для EX 250 2023

Бренды по названию

Популярные бренды

GAS GAS EX 250 2023, Руководство пользователя

Результаты поиска

Содержание EX 250 2023

Отзывы:

Похожие инструкции для EX 250 2023

Бренды по названию

Популярные бренды