GAS GAS EX 250 2023 Скачать руководство пользователя страница 65

Страница: 65 / 144

SERVICE WORK ON THE CHASSIS 11

E02023-11

–

Mount and tighten screws

Guideline

Screw, fuel tank spoiler

on radiator

6 Nm (4.4 lbf ft)

V01590-11

–

Plug in connector

for the fuel pump.

–

Remove the wash cap set and thoroughly clean the quick release

coupling using compressed air.

Info

Under no circumstances should dirt enter into the fuel line.

Dirt in the fuel line clogs the injection valve!

–

Spray silicone spray onto a lint-free cleaning cloth and lightly lubri-

cate the O-ring of the quick-release coupling.

Silicone spray (

p. 133)

–

Join quick release coupling

Info

Route the cable and fuel line at a safe distance from the

exhaust system.

Finishing work

–

Mount the seat. (

p. 55)

11.33

Checking the chain for dirt

400678-01

–

Check the chain for heavy soiling.
» If the chain is very dirty:

–

Clean the chain. (

p. 63)

11.34

Cleaning the chain

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

–

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Содержание EX 250 2023

















































































































































Результаты поиска

Содержание EX 250 2023

Отзывы:

Похожие инструкции для EX 250 2023

Бренды по названию

Популярные бренды

GAS GAS EX 250 2023, Руководство пользователя

Результаты поиска

Содержание EX 250 2023

Отзывы:

Похожие инструкции для EX 250 2023

Бренды по названию

Популярные бренды