GARO GDA2K-400 KNX Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 63

background image

Universal dimmer actuators GDA2K-400 KNX / GDA4K-400 KNX

pdated: Mai-17 (Subject to changes) Page 43 of 63

4.1.3 Driveway lighting

A motion detector activates the dimmer via the soft switching object.
The lighting is dimmed up within 5 seconds if a movement is detected.
This delay gives the eyes enough time to adjust to the light without being dazzled
The lighting is gradually dimmed down within a minute and then switched off after the configured
time has elapsed or a Soft OFF telegram is received via the button or via the motion detector (cyclic).

0 %

t(h)

100 %

A

t1=5s

t3 =1 Min.

t2

Min.

Val.

B

C

D

P

Sequence:

A

Soft ON

is sent by the motion detector:

The brightness is immediately adjusted to the configured

Minimum dimming value

t1

The brightness is gradually increased within the configured time for

Soft ON

(5 s)

B

Configured value after

Soft ON

is reached

t2

Time between

Soft ON (1) and Soft OFF

C

Soft OFF

telegram was received or configured time has elapsed:

Start of the

Soft OFF

phase

t3

The brightness is gradually reduced within the configured time for

Soft OFF

S

t3 has elapsed, the configured

Minimum dimming value

has been reached and the system dims

to 0%

«
...
41
42
43
44
45
...
»

Содержание GDA2K-400 KNX
































































Отзывы:

Нет отзывов

Похожие инструкции для GDA2K-400 KNX

Бренд: DAV TECH Страницы: 10

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

VLT DriveMotor FCP 106

Бренд: Danfoss Страницы: 4

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

GAT ACCESS 6100

Бренд: Gantner Страницы: 4

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: GBD Страницы: 15

Бренд: Parker Страницы: 21

Бренд: Parker Страницы: 26

Бренд: Parallax Страницы: 3

Бренд: Vageo Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: D+H Страницы: 32

Бренд: Maximum Controls Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды