GARO GDA2K-400 KNX Скачать руководство пользователя страница 23

Страница: 23 / 63

Universal dimmer actuators GDA2K-400 KNX / GDA4K-400 KNX

pdated: Mai-17 (Subject to changes) Page 23 of 63

Continuation:

Designation

Values

Description

Adjust soft switching

The standard values apply:
-

Time for Soft ON = 1 min

- Dimming value after Soft ON
= 100%
- Time between Soft ON and Soft
OFF = 5 min
- Time for Soft OFF = 1 min

yes..

The page

Soft switching

will be

shown and all parameters can be
adjusted individually.

Adjust block function

The standard values apply:
-

Block with ON telegram

- Behaviour when setting the
block
= 10%
- Behaviour when cancelling the
block = update

yes..

The page

Block function

will be

shown and all parameters can be
adjusted individually.

Activate force function

No force function.

yes..

The page

Force function

will be

shown.

Activate scenes

Do not use scenes.

yes..

The

Scenes

will be shown

Participation in central objects

Central objects are not taken into
account.

yes: in all central objects

only in central permanent ON

only in central permanent OFF

only in central switching

only in central switching and

permanent ON

only in central switching and

permanent OFF

only in central permanent On

and permanent OFF

Which central objects are to be
taken into account?

Central objects enable
simultaneous switching on and
off of several channels with one
single object.

Содержание GDA2K-400 KNX
































































Результаты поиска

Содержание GDA2K-400 KNX

Отзывы:

Похожие инструкции для GDA2K-400 KNX

Бренды по названию

Популярные бренды

GARO GDA2K-400 KNX, Руководство пользователя

Результаты поиска

Содержание GDA2K-400 KNX

Отзывы:

Похожие инструкции для GDA2K-400 KNX

Бренды по названию

Популярные бренды