background image

 

 

HD-2 Operation and Installation Manual

 

Page 1 

 

GENERAL INFORMATION 

 

INSPECTION 

Inspect the degausser for shipping damage as soon as it is unpacked.  If the degausser 
or any accessories are damaged or fail to operate correctly, notify carrier and Garner 
Products, Inc. immediately.  For assistance from Garner Products, Inc. call (916) 784-
0200 or fax (916) 784-1425.  For warranty information, please refer to the Warranty 
section inside this manual.   

 

INTRODUCTION 

The Garner Products, Inc. Model 

HD-2

  is a continuous duty capacitive discharge 

degausser.  The HD-2 is designed to erase hard drives and tape cartridges that fit 
inside the drawer.  The convenient drawer loading design accommodates many 
different types and sizes of media, without the need for adapters.   
 

 

MAGNETIC FIELDS 

 

Magnetic fields measured around perimeter 

The 

HD-2

 produces a single focused magnetic pulse lasting less than 1/20 of a second.  

The focused intensity allows the HD-2 to erase today’s highest coercivity media while 
also limiting the magnetic field exposure to 1 second for every  20 pieces of media 
degaussed.    

 

Distance from 

degausser 

Magnetic 

field(Front Panel) 

Magnetic 

field(Side) 

Duration of Field 

0cm (0 inches) 

620 gauss 

328 gauss 

< 0.05 Second 

10cm (4 inches) 

249 gauss 

81 gauss 

< 0.05 Second 

20cm (8 inches) 

85 gauss 

26 gauss 

< 0.05 Second 

30cm (12 inches) 

19 gauss 

8 gauss 

< 0.05 Second 

 

Note:

  The testing room measured 0.4 gauss before degausser was plugged in. 

 

 

Average Operational Distance (AOD) from user to the HD-2 is 12-18 inches (30-45cm).  
According to the American Conference of Governmental Industrial Hygienists (ACGIH) 
Threshold Limit Values (2005) - Static Magnetic Fields, whole body exposure limits 
recommended for an 8 hour shift are 600 gauss.  Because of the short duration of each 
pulse from an HD-2 (1/20

th*

 of a second) and the extremely small magnetic field outside 

of the unit (<19 gauss, AOD) the total 8 hour whole body exposure is 1/120

th

 of the 

recommended limit.   
 

*Pulse duration was rounded to ½ second per discharge for calculations to cover any build up of 
magnetic fields generated before or after discharge. 

 

 

Pace Maker Users 

Due to stray magnetic fields, consult your physician before operating. 

Содержание HD-2 Series

















Отзывы: