Garmin Nuvi 250 Скачать руководство пользователя | Manualshive

Страница: 97 / 112

background image

Comment memory full

-

The waypoint comment memory is full. You
must delete existing waypoint comments
before adding new ones.

Configuration reset

-

The GNC 250 has detected a failure in its
installation configuration memory. Data from
the user memory has been used to reset the
configuration. Check the installation settings
for correctness. If the message persists, the
unit is not usable and should be taken to an
authorized service center for repair.

Data card failed

-

The GNC 250 has detected a problem with
the data card. The data is not usable and the
card should be returned to Jeppesen or an
authorized GARMIN service center.

Data card write fail

-

The user data card failed to program. The
card should be returned to an authorized
GARMIN service center.

Degraded accuracy

-

The GNC 250 has detected poor satellite
geometry while RAIM is not available.
Additional cross-checking with a secondary
navigation source should be performed to
verify the integrity of the GPS position.

Do not use for nav

-

The GNC 250 is in the simulator mode and
must not be used for actual navigation.

EEPROM write fail

-

The GNC 250 has detected a failure while
programming its installation configuration
memory. The unit is not usable and should
be taken to an authorized service center.

Final altitude alert

-

The suggested altitude is within 1000 feet of
the final altitude entered on the VNAV
Planning page.

Fuel/Air input fail

-

The fuel and/or air data input is not available
to the GNC 250. Check the I/O settings or
fuel/air data system installation.

Inside SUA

-

You have entered a Special Use Airspace.

Invald CPA wpt _____ -

The closest point of approach cannot be created
from the waypoint entered on the CPA Page.
This occurs when the computed point does not
fall on one of the route legs, or when a unique
waypoint name for the closest point of approach
cannot be found.

Invalid copy route

-

A non-empty route was selected for a copy
operation. A route must be empty before
another route can be copied to it.

Invalid CPA route

-

The selected route contains less than two
waypoints and cannot be used for CPA oper-
ations.

Invalid SAR route

-

The selected route does not contain exactly
two waypoints and cannot be used for SAR
operations.

87

SECTION

D

MESSAGES &

ABBREVIATIONS

250 real 7/14/98 9:33 AM Page 87

«
...
95
96
97
98
99
...
»

Содержание Nuvi 250

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Nuvi 250

Бренд: RAK Страницы: 6

Бренд: Magellan Страницы: 2

Бренд: Magellan Страницы: 123

Бренд: Carscop Страницы: 11

Бренд: Haicom Страницы: 30

Бренд: CyBike Страницы: 2

Solar Bluetooth

Бренд: Hama Страницы: 35

Бренд: Navitel Страницы: 217

Бренд: ZeroKey Страницы: 18

Бренд: Queclink Страницы: 13

Бренд: Fleet Complete Страницы: 12

Бренд: Garmin Страницы: 2

GPS 31 SL TracPak

Бренд: Garmin Страницы: 28

Бренд: Magellan Страницы: 16

Бренд: Magellan Страницы: 34

Бренд: Magellan Страницы: 101

Бренд: Magellan Страницы: 116

Бренд: Magellan Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды