Garmin Nuvi 250 Скачать руководство пользователя | Manualshive

Страница: 100 / 112

background image

Searching the sky

-

The GNC 250 is in the search-the-sky mode.
Allow the unit to complete data collection
before turning it off.

Start altitude chng

-

The altitude change entered on the VNAV
Planning page is about to begin.

Steep turn ahead

-

This message appears approximately 90 sec-
onds prior to a turn that requires a bank angle
in excess of 25 degrees in order to stay on
course. Turn anticipation will not be provided
for the turn.

Stored data lost

-

Stored user data, including waypoints, routes
and satellite orbital data have been lost due to
a low memory battery or inadvertent master
reset.

Stuck mic/tx disabled

-

The microphone/headsets have been transmit-
ting continuously for 35 seconds, and the
transmitter has been disabled. Releasing the
transmit key will allow you to transmit again.
If this message persists, check the installation.

SUA ahead < 10 min

-

The projected course and current speed will
take you inside an SUA within the next 10
minutes.

SUA near & ahead

- Your position is within two nautical miles of

an SUA and your current course will take
you inside.

Timer expired

-

The approach timer has expired.

User data RX started

-

Data receive operations have started.

Usr data TX complete

-

Data transmit operations are complete.

VNAV cancelled

-

The VNAV function has been cancelled due to a
change in the active route.

WGS 84 datum selectd -

The system map datum was changed to
WGS 84 because the selected map datum
has been removed from the NavData card,
the data card is missing, or the data card has
failed.

Wpt comment locked

-

At least one waypoint comment is locked
because the waypoint has been removed
from the Jeppesen NavData®, the data card
is missing, or the data card has failed.

Wpt exists _____

-

You have entered a waypoint name on the
AutoStore™ Page or User Waypoint Catalog
Page that already exists in memory. Enter a
waypoint name that does not exist.

Wpt memory full

-

The waypoint memory is full. You should
delete unused waypoints to make room for
new waypoints.

90

APPENDIX D

Messages &

Abbreviations

SECTION

D

MESSAGES &

ABBREVIATIONS

250 real 7/14/98 9:33 AM Page 90

«
...
98
99
100
101
102
...
»

Содержание Nuvi 250

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Nuvi 250

Бренд: RallyTrack Страницы: 3

Бренд: Garmin Страницы: 16

Бренд: Garmin Страницы: 48

Бренд: Alpine Страницы: 230

Бренд: Mappy Страницы: 40

Бренд: Haicom Страницы: 47

Бренд: Navman Страницы: 16

Бренд: Daviscomms Страницы: 35

Бренд: Garmin Страницы: 132

Бренд: FCC Страницы: 6

Бренд: Navitel Страницы: 24

Бренд: Yada Страницы: 16

Бренд: Packard Bell Страницы: 10

Бренд: Becker Страницы: 28

Бренд: Life Minder Страницы: 12

TimeSource 3100

Бренд: Symmetricom Страницы: 238

Бренд: MVP Recovery Страницы: 6

PocketTracker 1442

Бренд: Teletype Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды