Part # 4517125 Rev. 2 (01/09/12)
Page 7
INSTALLATION
IMPORTANT: Rating plate for this appliance is located on
the right side panel.
This equipment must be installed by a competent factory
trained, certified, licensed and / or authorized service or
installation person.
Swivel Caster Installation
Prior to installation, the four casters, supplied loose with the
grill, must be securely located on the underside of the base.
The casters fitted with a brake must be located at the front of
the grill.
1. Carefully remove the top and side packaging leaving the
grill on shipping pallet.
DO NOT REMOVE THE TIES SECURING THE PLATEN ARMS
TO THE GRILL TOWEL BAR.
2. Raise the grill vertically off the pallet to a comfortable
working height and install the casters. DO NOT TIP THE
GRILL ON ITS BACK OR SIDE. If a truck lift is used, be
careful when inserting the lifting arms under the grill as
the gas inlet elbow is protruding in the center of the base.
WARNING - GRILL WEIGHT IS APPROXIMATELY 800 LBS –
USE CAUTION
3. Install the casters as shown below. The two casters with
brakes go on the front, and the two without on the rear.
WITH
BRAKE
WITHOUT
BRAKE
NOTE: CASTERS MUST BE THREADED INTO GRILL BASE
LEAVING APPROXIMATELY ONE INCH OF EXPOSED
THREAD. THIS IS THE STARTING POINT FOR LEVELLING THE
GRILL AFTER IT IS IN POSITION.
The grill is to be located directly under ventilation system.
Once installed in the grill station underneath the ventilation
system, the platens, in their highest position, must not
interfere with the lower lip of the ventilation system hood.
The raised position of each platen is adjusted by raising
or lowering the upper of the two microswitches, (limit
switches), in the rear of the grill. The lower microswitch
position must not be adjusted.
Grill plate must be level front to back, side to side and
diagonally. This leveling must be done with the unit under
the hood and in it’s normal operational position to prevent
warping of the grill plate.
NOTE:
Fuses are installed to prevent damage in the event of
failure of the upper microswitch.
Electrical Connections:
WARNING:
This appliance must be properly grounded.
All electrically operated appliances must be electrically
grounded in accordance with local codes; or in the absence
of local codes, with the latest edition of National Wiring
Regulations. A wiring diagram is located on the rear panel of
the grill. See rating plate in rear of grill, or lower front panel
for proper voltages.
This appliance should be connected to a potential
equalization system. A labeled equipotential bonding point
is fitted to the rear of the grill.
It is recommended that this grill be connected to a residual
current,, (earth leakage),, device with a tripping current not
exceeding 30mA. The leakage current of this grill will not
exceed 5mA.
CAUTION:
Prior to installation, check the electrical supply
to ensure input voltage and phase match the equipment
voltage rating and phase. See data plate located rear left side
of grill and lower front panel.
National Codes Requirements:
In Canada, electrical connection must comply with
applicable sections of the Canadian Electrical Code, C22.1
- 1990, latest edition, “Safety Standard for Installation,
Part 1” and C22.2- No. O-M 1982 latest edition , “General
Requirements, Part 2”.
Содержание XE24
