English
40/120
Use this machine for the purpose for which it was
designed. Any other use may be dangerous for the
user, for the machine and for persons, animals and
things that may be around.
Check:
- The machine completely and look for loose and
damaged parts (screws, nuts, etc.).
- That the moving parts of the machine are not in
contact with any other object.
Tighten, repair or replace everything you need before
using the machine.
Do not use any accessory on this machine outside of
those recommended by Garland since its use could
result in serious injury to the user, machine, and the
people, animals and things close to the machine.
Check the oil level and make sure that it is between
the two marks on the dipstick that can be found under
the oil plug (9) input. If it is below the lowest level you
should refill the oil.
Check that there are no oil leaks in the machine. If you
detect leaks bring your machine in for service.
Check the cable and the switch status. If you notice
any abnormalities do not start the machine and take it
in for service.
5.3.3. STARTING AND STOPPING THE MACHINE
1. Loosen the bleed screw until
the air can enter and exit the oil
tank without problems. The flow
of air that out through the bleed screw hole should be
detectable during operation of the appliance. If you do
not loosen the bleed screw, the air inside the hydraulic
system cannot leave, thus compressing itself with
every cutting motion of the bandsaw. This air pressure
can damage the hydraulic system’s seals, causing
permanent damage to the machine.
2. Turn on the engine by pressing the green button.
Note: When the temperature is low, let the bandsaw
run idle for approximately 15 minutes so that the oil
heats to the right temperature.
3. Put the trunk (1) on the table (2) and secure using
the clamp (3).
4. Cutting begins when you push both operation
levers down (as soon as the cutting blade comes
into contact with the wood, slightly loosen while is
continuous downward pressure on the levers, this
will prevent the clamps (arms) from being bent.
Note: This bandsaw is equipped with a “ZHB” control
system that requires two hands to be used. The
3
1
2
Plug screw
Содержание CHOPPER 406 VE
