Part # P128 Rev 5 (05/29/09)
Page 5
INSTALLATION
Serial Plate Location
All burner inputs are shown on the Serial/Rating Plate of
each unit, located on the bottom of the control section near
the front.
When corresponding with the factory or your local
authorized factory service center regarding service problems
or replacement parts, be sure to refer to the particular unit
by the correct model number (including the prefix and suffix
letters and numbers) and the warranty serial number. The
rating plate affixed to the unit contains this information.
We suggest installation, maintenance and repairs should be
performed by your local authorized service agency listed in
your information manual pamphlet.
*OUIFFWFOUZPVIBWFBOZRVFTUJPOTDPODFSOJOHUIF
installation, use, care or service of the product, write or call
our Product Service Department.
This product must be installed by professional personnel as
specified. Garland/U.S. Range products are not approved or
authorized for home or residential use, but are intended for
commercial applications only. Garland / U.S. Range will not
provide service, warranty, maintenance or support of any
LJOEPUIFSUIBOJODPNNFSDJBMBQQMJDBUJPOT
General Information
%BNBHF$IFDLDIFDLDBSUPOPSDSBUFGPSQPTTJCMFEBNBHFT
JODVSSFEJOTIJQQJOH"GUFSDBSFGVMMZFYBNJOJOHDIFDLGPS
“Concealed” damage. Report any damage immediately to
your carrier.
Legs, Casters & Leveling
1. The unit must be installed on the legs or casters
provided. A minimum 4 inch (101 mm) air space must
CFNBJOUBJOFECFMPXUIFVOJUGPSSFRVJSFEBJSøPXUPUIF
burner systems. Avoid placing any objects under the unit
XIJDIDPVMEPCTUSVDUBJSøPXUPUIFCVSOFSTZTUFNT
'PSNPEFMTFRVJQQFEXJUIDBTUFSTUIFJOTUBMMBUJPO
shall be made with a connector that complies with the
Standard for Connectors for Moveable Gas Appliances,
ANSI Z21.69/CSA 6.16, Addenda Z21.69B-2006/CSA
# PSMBUFTUFEJUJPOBOEBRVJDLEJTDPOOFDU
EFWJDFUIBUDPNQMJFTXJUIUIF4UBOEBSEGPS2VJDL
Disconnects for Use with Gas Fuel, ANSI Z21.41/CSA
6.9, Addenda Z21.41A-2005/CSA 6.16A-2005 (or latest
edition).
"EFRVBUFNFBOTNVTUCFQSPWJEFEUPMJNJUNPWFNFOUPG
the appliance without depending on the connector and
RVJDLEJTDPOOFDUEFWJDFPSBTTPDJBUFEQJQJOH5IJTDBO
be accomplished by attaching restraining chains/cables
GSPNøPPSPSSFBSXBMMUPSFBSPGVOJU
4. When the unit is installed in its operating location, level the
unit by adjusting the leveling legs. Use a level across the
front rear, and sides of each unit.
NOTE: The griddle plate may not rest
evenly on the unit body if the unit is
not properly leveled.
5. Each caster has a threaded stem
to aid in leveling only. No caster
should be adjusted beyond
a maximum of one-half inch,
(1/2”/13mm) of exposed thread
XJUIUIFMPDLJOHOVUUJHIUBHBJOTU
the stand leg, as shown.
Clearances
This unit must be installed in accordance with the following
clearances in order to provide proper operation and
servicing of the appliance. Also, it is recommended that the
unit be installed with sufficient clearance. See chart below.
Clearances
Sides
#BDL
Left Right
Combustible
6”
(152mm)
6”
(152mm)
6”
(152mm)
Noncombustible
0”
0”
0”
Service
/PU3FRVJSFE
Type of Floor or Base
Combustible
Gas Connections
1. A readily accessible gas shut-off valve is provided on each
unit, attached to the main manifold under the unit. Gas
supply connection must be made with minimum 3/4 inch
NPT pipe. Larger than 3/4 inch (19 mm) supply pipe may
CFSFRVJSFEXIFOBMPOHSVOPGTVQQMZQJQFJTOFDFTTBSZ
Consult the pipe capacity tables in the installation code.
1
/2"
(
1
3mm)
MAX
Содержание CG-24R
Страница 12: ...Pi ce n P128 Rev 5 05 29 09 Page 13...
