English
English
37/148
- Insert the filled 0,6 l of oil tube.
- Wait 1 minute for the oil to completely go down to
the crankcase.
- Clean the dipstick from the oil with a cloth.
- Insert the rod and screw on the oil cap.
- Unscrew the plug again and check the mark left
by oil on the dipstick. The mark left by the oil must
be between the minimum and maximum marks.
- If the mark is below the minimum, add a little more
oil and recheck.
- If the mark is above the maximum, you will have
to remove oil from the crankcase. To do this, tilt the
machine and let out a little oil (put a container
at the end of the tube to prevent oil spilling on the
machine or the ground).
6.4. START-UP
6.4.1. CHECKPOINTS BEFORE COMMISSIONING
The machine must be mounted and must be used
according to the following instructions:
Before starting the engine, ensure that the entry chute
is completely empty. If not, clean the entry chute with
the use of a stick or something long.
Maintain hands, other extremities and clothes clear of
the entry hopper, clear of the exit shoot and clear of all
rotating elements.
Maintain a good balance on both feet.
Do not lean on the machine.
Maintain yourself well clear of the exit area whilst the
machine is working.
If the blades hit a strange object (any other object
different to wood) or if the machine starts to make
strange noises and/or it vibrates in an abnormal way,
stop the engine so that the blades stop turning. Take
the machine to your nearest service agent for repair.
If the machine gets stuck, you must stop it and wait
for the blades to stop turning.
The use of working
gloves, ear protection
and working glasses is
mandatory.
The machine is designed only for outdoor use. Avoid
using the machine in outdoor areas with a high
probability of exhaust fumes.
The machine must be used by only one person at a
time.
Never insert your hands in the entry chute until the
machine has been stopped and the blades have
stopped rotating.
The pieces of wood that might have got stuck
transversally must only be removed when the machine
has been stopped and the blades have stopped
rotating.
Содержание 1080 TQG
