12
Take the outer flange off after release the nut, then
put the blade (17), outer flange (17b), shield (17a)
and nut according to priority as below picture. Note
the blade rotation direction needs be same as below
picture. Use screw driver to hold flange and tighten
nut counter-clockwise, ensure the nut is tightened
enough.
•
Release blade. Use screw driver to hold flange and
release nut, the blade can be took off.
m
Warning!
Please make sure the cutting head has been assem-
bled correctly before use!
Note:
The packaging material is made of recycled ma-
terials. Dispose of packaging materials in accordance
with regulations.
5.
Fit the belt. Fig. 13-15
•
The combined petrol grass trimmer, pole saw, brush
cutter must be used with the strap.
•
Balance the machine when the tool is switched off.
•
Wear the shoulder strap.
•
Adjust the strap length so that the snap hook (k) is
about a hand‘s breadth below the right hip.
•
Hang the petrol brush cutter on a hook.
•
Hang the machine.
•
When standing in a normal working posture, the
blade should touch the ground during normal work-
ing position.
•
Thereby, it is important that the petrol brush cutter is
always well balanced.
•
For operation, hook the petrol brush cutter into the
snap hook (k) of the carrying strap while the engine
is running.
•
ATTENTION! In an emergency, the safety latch (l)
can be pulled from the harness. The machine then
detaches immediately from the carrying strap (9)
and falls to the ground.
OPERATION
When working with the equipment as grass trimmer
and brush cutter, the appropriate plastic guard hood
for cutting blade mode or cutting line mode must be fi
tted to prevent objects being thrown out by the equip-
ment.
The integrated blade (A) in the cutting line guard hood
automatically cuts the line to the optimum length.
Fig. 18
Filling with fuel
m
Danger of injury! Fuel is explosive!
Turn off and cool the motor down before filling
the tank with fuel. You must observe all safety
instructions relating to handing fuel.
m
Risk of device damage!
The device is supplied without motor or gearbox
oil.
ATTENTION! Before operating, you must fill it
with fuel.
fuel into an airtight container and keep it in the dark and
cool room.
2
Fuel mixing table
Mixing procedure: 40 parts petrol to 1 part oil
Example:
1 l Petrol : 0.025 l 2-stroke oil
5 l Petrol : 0.125 l 2-stroke oil
Warning!
Take care of the emission of exhaust gases.
Always shut off engine before fueling. Never add fuel
to a machine with a running or hot engine. Take care
of fire!
XI. Attachment and operation
ASSEMBLY
When assembling this machine, please follow the in-
structions for assembly printed.
1
Assemble the handle on the machine. Fig. 2-3
•
Install the front handle as shown on the image 2.
•
Make sure that you align the pin with the hole. Tight-
en the screws only loosely before you have the most
comfortable working position set to the risers. The
front handle should be aligned as in pictures 2+3
shown, then tighten the screws.
2.
Mounting the shaft. Fig. 4
•
Pull out the locking pin (a) and press the lower part
of the shaft (b) downward until the locking pin en-
gages. The bolt (a) is in the right position when it is
fully seated in the bore.
•
Lastly, tighten the knob (d) securely.
3.
Assemble the safe guard. Fig. 5-7
•
Fix the safe guard with hex key and wrench en-
closed as standart accessories for tighting the nuts
enough. Please see the below pictures showing.
m
Warning!
Use only original manufacturer‘s replace-
ment parts, accessories and attachments. Failure to
do so can cause poor performance, possible injury and
may void your warranty. Never use the machine with-
out the guard assembled!
4.
Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 8-9
•
Release the nut.
Line up the two holes of flange and shield, use one
screw driver to hold the flange as below and turn the
socket wrench clockwise, the nut will be released.
•
Fit the Nylon cutting head.
Remove another shield after release the nut. Still hold
the flange, take the Nylon cutting head on the shaft
and rotate counter-clockwise, the Nylon cutting head
is fitted. Fig. 8/9
•
Release the Nylon cutting head.
Use screw driver to hold flange and then rotate the
Nylon cutting head clockwise, it will be replaced.
Brush cutter / Cutter blade
•
Fit the blade. Fig. 10-12
13
AFTER SALES SUPPORT TEL: 1300 855 831 WEB: www.scheppach.com.au
AFTER SALES SUPPORT TEL: 1300 855 831 WEB: www.scheppach.com.au
