the distance. Enter the displayed number of metres in
the
Distance field for the working area in question.
If
Remote start 2 has been activated, i.e. if another
option other than Never has been selected for
Proportion, these settings must also be tested. Remote
start 2 test is performed in the same way as for Remote
start 1.
3.14.4.2 Test IN
The
Test IN function allows you to test how well the
robotic lawnmower docks with the charging station.
Note:
Test IN can only be performed after Test OUT has
been performed.
Selecting this function causes the robotic lawnmower to
travel directly along the guide wire towards the charging
station and to dock with it. The test is approved only if
the robotic lawnmower is able to dock with the charging
station at the first attempt. If the robotic lawnmower is
unable to dock on the first attempt, it will automatically
try again. The installation is not approved if the robotic
lawnmower needs two or more attempts to dock with the
charging station.
3.14.5 Drive past wire
The front of the robotic lawnmower always passes the
boundary wire by a specific distance before the mower
turns around. The default distance is 25 cm, but this can
be changed if required. The minimum value is 20 cm
and the maximum value is 30 cm. Note that the distance
given is only an approximate value. In reality, the actual
distance the robotic mower passes the boundary wire
can vary.
Specify the number of centimetres you want the robotic
lawnmower to pass the boundary wire and press
OK.
3.15 Security
Through this selection, settings relating to security and
the connection between the mower and the charging
station can be made.
SECURITY
Change PIN code
Security level
New loop signal
3.15.1 Change PIN code
Enter the new PIN code and press
OK. Enter the same
code again and confirm by pressing
OK. When the PIN
code is changed, the message
PIN code changed
appears in the display.
Make a note of the new PIN code on the designated line
on the
MEMO. See Introduction on page 3
3.15.2 Security level
There are 3 security levels to choose from.
Security level
Low
Medium
High
Low and Medium security prohibits access to the robotic
lawnmower if the PIN code is unknown.
High security
also includes a warning that beeps if the correct PIN
code is not entered after a designated time period.
If the wrong PIN code is entered 5 times in succession
the robotic lawnmower is blocked for a time. The
blockage time is extended for every new incorrect
attempt.
Function
Low
Medium
High
Time lock
X
X
X
PIN request
X
X
Alarm
X
3.15.2.1 Time lock
This function means that the robotic lawnmower cannot
be started after 30 days without first entering the correct
PIN code. When the 30 days has passed the robotic
lawnmower will continue to mow as normal, but the
Enter PIN code message appears when the hatch is
opened. Enter your code again and press
OK.
3.15.2.2 PIN request
This function means that the robotic lawnmower
requests a PIN code when the main switch is set to
1
and each time the hatch is opened. The correct PIN
code must be entered to use the robotic lawnmower.
If the wrong PIN code is entered 5 times in succession
the robotic lawnmower is blocked for a time. The
blockage time is extended for every new incorrect
attempt.
3.15.2.3 Alarm
This function means that an alarm sounds if the PIN
code is not entered within 10 seconds after the STOP
button has been pressed or the robotic lawnmower has
been lifted up for any reason. A ticking noise indicates
that the PIN code must be entered to prevent triggering
the alarm. The alarm can be turned off at any time by
entering the correct PIN code.
3.15.3 New loop signal
The loop signal is randomly selected to create a unique
link between the robotic lawnmower and the charging
station. In rare cases, there may be a need to generate
a new signal, for instance if two adjacent installations
have a very similar signal.
1. Place the robotic lawnmower in the charging station.
2. Select
New loop signal in the menu.
26 - Installation
303 - 001 - 21.09.2017
