GARDEN MASTER GM3815 Скачать руководство пользователя страница 7

Страница: 7 / 8

If you choose to vary from these instructions your

warranty will be impaired.

If you need advice, call us

FREE

0800 807 433

or email us at [email protected]

KITSET WOODEN FLOORS

Every shed must have a floor. These are available from your local shed dealer.
For more information visit www.gardenmastersheds.co.nz

RECESSED FLOOR CLAMPS

For poured floors with a

recess around the perimeter.
Available from your

shed dealer.

FLAT FLOOR CLAMPS

For existing concrete only.

Water can seep underneath.
Available from your

shed dealer.

BOXING DIAGRAM

20MM - 25MM

(1 ' X 1 ')

INTERNAL DIMENSIONS

APPROX 25MM RECESS

AROUND THE OUTSIDE

25MM

3725MM

INTERNAL

MEASUREMENT

1485MM

PEG THE FLOOR TO THE GROUND IN WINDY AREAS

RUNNER

SHED

FLOOR BOARD

SHED

RECESS

20MM - 25MM

8MM BOLT SET INTO CONCRETE

100MM

25MM

APPROX

20MM - 25MM

3725MM X 1485MM

INTERNAL DIMENSIONS FOR THE GM3815:

STEP 7:

COMPLETE YOUR SHED

RECESSED CONCRETE FLOOR PLAN FOR

SPECIALLY POURED CONCRETE FLOORS:

SPECIFICATIONS

Every shed must have some type of foundation between it and the ground. You can pour a concrete floor and use recessed floor
clamps, use an existing concrete base with flat floor clamps or purchase a kitset wooden floor from your shed dealer.

Содержание GM3815









Результаты поиска

Содержание GM3815

Отзывы:

Похожие инструкции для GM3815

Бренды по названию

Популярные бренды

GARDEN MASTER GM3815, Руководство по сборке

Результаты поиска

Содержание GM3815

Отзывы:

Похожие инструкции для GM3815

Бренды по названию

Популярные бренды