Gantner GL7p Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 68

Gantner GL7p Скачать руководство пользователя страница 63

GL7p - Battery-powered, door-mounted electronic locker lock GL7p
Operation

www.gantner.com

HB_GL7p--EN_12

63

7

CLEANING AND MAINTENANCE

This chapter contains information for the cleaning personnel and service technicians responsible for the cleaning and
maintenance of the GL7p locks and lockers.

ATTENTION!

The instructions described in this chapter may only be carried out by suitably trained personnel.

The warnings in this chapter must be observed and followed during functional testing, cleaning, and maintenance.

7.1 Cleaning

Regular cleaning of the locker components ensures that the locker system remains in good condition and the
correct working order is maintained.

NOTE!

Do not use cleaning benzene, diluents, or other abrasive detergents. In addition, the components must not

be cleaned using a high-pressure or steam cleaner otherwise damage can occur!

Complete the following steps to clean the locker:

► Wipe off dirt and dust using a soft, lint-free, dry cloth.

► For extreme dirt, clean the locker components using a slightly moistened cloth. Do not allow any moisture to

enter the inner parts of the GL7p.

7.2 Maintenance

The GL7p system components are maintenance-free, i.e., maintenance of the mechanical parts is not required.
Should a malfunction be detected during functional testing that cannot be remedied, the corresponding faulty part(s)
must be replaced.

7.3 Functional Testing

To ensure that the locker locks are functioning correctly, periodically test the functionality of the locker doors and

lock components.

Frequency

- After every 1000 locking operations, or,

- If the locking function of a locker door is impaired.

Instructions

► Close the locker door.

o

The door must close shut without increased effort. Readjust the door (see below) if this does not happen.

► Lock the door. Depending on the type of lock (data carrier or PIN code), press the GL7p button in with a valid

data carrier or enter a valid PIN code when the door is closed.

o

The locker door must lock. If it does not, check that the data carrier authorization is valid.

«
...
61
62
63
64
65
...
»

Содержание GL7p





































































Отзывы:

Нет отзывов