Gantner GAT NET.Lock 7020 System Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 64

background image

GAT NET.Lock 7020 System

Installation

30

HB_GAT-NETLOCK7020--EN_12

www.gantner.com

3.11

Installation in Lockers with Metallic Doors

The GAT NET.Lock 7020 can be installed on the left or right side of the inner locker wall depending on whether it is
a right or left-hinged locke

r door (see “3.7. Definition of the Door Hinge (Right or Left Door)). Two cutouts are required

in the door - one in the inner door sheet and one in the outer door sheet. The two parts of the GAT NET.Lock Bolt Set
7220 are mounted into these cutouts in the locker door. The door thickness must be between 18 and 26 mm (0.71 in
and 1.02 in). See Figure 3.10 and the following steps installation instructions.

1.  GAT NET.Lock 7020
2.  GAT NET.Lock Bolt Set 7220
3.  3 x mounting holes for the GAT NET.Lock 7020
4.  4 x mounting holes for the GAT NET.Lock BoltSet 7220
5.  LED position
6.  Label carrier
7.  Front label
8.  Cutout for GAT NET.Lock Bolt Set 7220
9.  Cutout for label carrier

Figure 3.10 - Installation in a locker with metallic door (right-hinged)

«
...
28
29
30
31
32
...
»

Содержание GAT NET.Lock 7020 System

































































Отзывы:

Нет отзывов

Похожие инструкции для GAT NET.Lock 7020 System

DePuy Synthes CSLP

Бренд: Johnson & Johnson Страницы: 13

Бренд: Auslock Страницы: 12

Бренд: Kwikset Страницы: 18

Alpha Titan 900

Бренд: BURG-WACHTER Страницы: 4

Бренд: ERA Страницы: 2

Бренд: Yale Страницы: 20

Real Living Assure Lock YRD226

Бренд: Yale Страницы: 24

Бренд: Dormakaba Страницы: 2

Бренд: PROMIX Страницы: 4

Бренд: PROMIX Страницы: 8

Бренд: Secu Страницы: 3

Бренд: DESi Страницы: 30

Stock Locks C425519RL

Бренд: COMPX Страницы: 1

Stock Locks C4198

Бренд: COMPX Страницы: 1

Бренд: Iseo Страницы: 4

Бренд: LEHMANN Страницы: 20

K100-620 Aperio Series

Бренд: HES Страницы: 10

Бренд: hager Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды