Gantner GAT NET.Lock 7020 System Скачать руководство пользователя страница 5

Страница: 5 / 64

GAT NET.Lock 7020 System

www.gantner.com

HB_GAT-NETLOCK7020--EN_12

2. Property Damage Messages

Property damage messages are used to describe potentially hazardous situations that may lead to property damage. These

essages have the same layout as safety messages but use the signal word "NOTICE" instead of “CAUTION”.

Format of property damage messages that apply to an entire section:

Risk of damage to the device and connected devices
Risk of malfunction

- Read the following instructions carefully before installing the device.

- Always adhere to the instructions.

Format of property damage messages that are embedded in text and apply to a specific
point:

NOTE!

Risk of damage to the device and connected devices.

Read the following instructions carefully before installing the

device.

3. Definition of the Signal Words

Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates information considered important, but not hazard-related (e.g., messages relating to

property damage).

4. Definition of the Safety Symbols

Caution: General Information

This symbol indicates general warnings or cautions that are not related to a particular type of hazard.

Caution: Electrical Shock

This symbol indicates warnings related to electrical hazards (danger due to high voltage).

Prohibited: Do Not Disassemble

This symbol indicates warnings about not disassembling certain components or equipment. Disassembling may
lead to damage or malfunction of the device.

Mandatory Action: General Information

This symbol indicates general information that must be read and followed before proceeding with the
accompanying instructions.

Mandatory Action: Read Instructions

This symbol indicates information referring to an important description in the manual, or other documentation,
which must be read and followed.

Содержание GAT NET.Lock 7020 System

































































Результаты поиска

Содержание GAT NET.Lock 7020 System

Отзывы:

Похожие инструкции для GAT NET.Lock 7020 System

Бренды по названию

Популярные бренды

Gantner GAT NET.Lock 7020 System, Установка, настройка и эксплуатация

Результаты поиска

Содержание GAT NET.Lock 7020 System

Отзывы:

Похожие инструкции для GAT NET.Lock 7020 System

Бренды по названию

Популярные бренды